2014 Hilux · Service Manual TRANSMISSION

REPLACEMENT

Removal / installation · Vehicles built from Jun 2011


1. REMOVE TRANSFER SHIFT LEVER KNOB SUB-ASSEMBLY

B277221
  1. Twist the shift lever knob in the direction indicated by the arrow and remove it.


2. REMOVE PARKING BRAKE HOLE COVER SUB-ASSEMBLY

B278222
  1. Detach the 4 claws and remove the parking brake hole cover.


3. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY

  1. Detach the 12 claws and remove the upper console panel.

    NOTICE:
    Be careful not to damage the instrument panel and console box with the claws of the upper console panel.


    B277548E01
    Text in Illustration 
    *A
    for 2WD
    *B
    for 4WD


4. REMOVE CONSOLE BOX ASSEMBLY

B278048E01
  1. Remove the 4 screws and 2 bolts.

  1. Using a clip remover, remove the 2 clips and console box.

    Text in Illustration 
    *1
    Screw
    *2
    Bolt
    *3
    Clip


5. REMOVE TRANSMISSION CONTROL CABLE ASSEMBLY

G034281E01
  1. Move the shift lever to L.

  1. Disconnect the control cable from the shift lever.

  1. Remove the lock clip and disconnect the control cable from the bracket.

  1. G034282E01
    Remove the 2 nuts and disconnect the control cable from the vehicle body.

  1. C219900
    Remove the 2 nuts and disconnect the ground cable and transmission control cable support.

  1. G034515E01
    Remove the lock clip and control cable bracket.

  1. Remove the nut and control cable.


6. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY
  1. Install the control cable with the nut.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }

  1. Install the control cable bracket and lock clip.

  1. C219900
    Connect the transmission control cable support and ground cable with the 2 nuts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. G034282E01
    Connect the control cable to the body with the 2 nuts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. G034281E01
    Connect the control cable to the bracket with the lock clip.

  1. Move the shift lever to L.

  1. Install the control cable to the shift lever.


7. ADJUST SHIFT LEVER POSITION

G034515E01
  1. Remove the nut and disconnect the control cable.

  1. Remove the clip and disconnect the control cable from the control cable bracket.

  1. C236140E01
    Push the control shaft rearward as much as possible.

  1. Return the control shaft lever 2 notches to the N position.

  1. While holding the control shaft lever slightly toward the R position side, tighten the nut.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }


8. INSPECT SHIFT LEVER POSITION
  1. When moving the shift lever from P to R with the ignition switch ON and the brake pedal depressed, make sure that the shift lever moves smoothly and correctly into position.

  1. Start the engine and make sure that the vehicle moves forward after moving the shift lever from N to D, and moves rearward after shifting to R.
    If the results are not as specified, inspect the park/neutral position switch and check the shift lever.


9. INSTALL CONSOLE BOX ASSEMBLY

B278048E01
  1. Install the console box with the 4 screws and 2 bolts.

  1. Install the 2 clips.

    Text in Illustration 
    *1
    Screw
    *2
    Bolt
    *3
    Clip


10. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY

  1. Attach the 12 claws to install the upper console panel.

    B277548E01

    Text in Illustration 
    *A
    for 2WD
    *B
    for 4WD


11. INSTALL PARKING BRAKE HOLE COVER SUB-ASSEMBLY
  1. Attach the 4 claws to install the parking brake hole cover.


12. INSTALL TRANSFER SHIFT LEVER KNOB SUB-ASSEMBLY

B277222
  1. Install the shift lever knob and twist it in the direction indicated by the arrow.

← INSPECTION (from Jun 2011)COMPONENTS (from Jun 2011) →