2014 Hilux · Service Manual TRANSMISSION

REPLACEMENT

Removal / installation · Vehicles built from Jun 2011


1. REMOVE PARKING BRAKE HOLE COVER SUB-ASSEMBLY

B278222
  1. Detach the 4 claws and remove the parking brake hole cover.


2. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY

  1. Detach the 12 claws and remove the upper console panel.

    NOTICE:
    Be careful not to damage the instrument panel and console box with the claws of the upper console panel.


    B277548E01
    Text in Illustration 
    *A
    for 2WD
    *B
    for 4WD


3. REMOVE CONSOLE BOX ASSEMBLY

B278048E01
  1. Remove the 4 screws and 2 bolts.

  1. Using a clip remover, remove the 2 clips and console box.

    Text in Illustration 
    *1
    Screw
    *2
    Bolt
    *3
    Clip


4. REMOVE TRANSMISSION CONTROL CABLE ASSEMBLY

G034281E01
  1. Move the shift lever to L.

  1. Disconnect the control cable from the shift lever.

  1. Remove the lock clip and disconnect the control cable from the bracket.

  1. G034282E01
    Remove the 2 nuts and disconnect the control cable from the vehicle body.

  1. G034514E01
    Remove the nut and disconnect the control cable from the vehicle body.

  1. G034515E01
    Remove the nut and clip and disconnect the control cable.


5. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY
  1. Install the control cable with the nut.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }

  1. G034514E01
    Connect the control cable to the vehicle body with the nut.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. G034282E01
    Connect the control cable to the body with the 2 nuts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. G034281E01
    Connect the control cable to the bracket with the lock clip.

  1. Move the shift lever to L.

  1. Install the control cable to the shift lever.


6. ADJUST SHIFT LEVER POSITION
  1. Move the shift lever to N.

  1. G034515E02
    Remove the nut and disconnect the control cable.

  1. C236140E01
    Turn the control shaft lever clockwise until it stops, and then turn it counterclockwise 2 notches to set it to the N position.

  1. While holding the control shaft lever slightly toward the R position side, connect the cable with the nut.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }


7. INSPECT SHIFT LEVER POSITION
  1. When moving the shift lever from P to R with the ignition switch to ON and the brake pedal depressed, make sure that the shift lever moves smoothly and correctly into position.

  1. Start the engine and make sure that the vehicle moves forward after moving the shift lever from N to D, and moves in reverse after shifting to R.
    If the results are not as specified, inspect the park/ neutral position switch and check the shift lever.


8. INSTALL CONSOLE BOX ASSEMBLY

B278048E01
  1. Install the console box with the 4 screws and 2 bolts.

  1. Install the 2 clips.

    Text in Illustration 
    *1
    Screw
    *2
    Bolt
    *3
    Clip


9. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY

  1. Attach the 12 claws to install the upper console panel.

    B277548E01

    Text in Illustration 
    *A
    for 2WD
    *B
    for 4WD


10. INSTALL PARKING BRAKE HOLE COVER SUB-ASSEMBLY
  1. Attach the 4 claws to install the parking brake hole cover.

← INSPECTION (from Jun 2011)COMPONENTS (from Jun 2011) →