REASSEMBLY
Removal / installation · Vehicles built from Aug 2012
Versions by build date: Jun 2011 – Jul 2012 from Aug 2012
| 1.
INSTALL INPUT SHAFT OIL SEAL RING |
 |
Coat the 3 oil seal rings with ATF.
Squeeze the ends of the 3 oil seal rings together, and then install them to the forward clutch drum groove.
- NOTICE:
- Do not expand the ring excessively.
- HINT:
- After installing the oil seal rings, check that they rotate smoothly.
| 2.
INSTALL FORWARD CLUTCH PISTON O-RING |
 |
Coat a new O-ring with ATF, and install it on the forward clutch drum.
Coat 2 new O-rings with ATF, and install them on the forward clutch piston.
| 3.
INSTALL FORWARD CLUTCH PISTON |
 |
Be careful not to damage the O-ring, and press the clutch piston into the forward clutch drum with both hands.
| 4.
INSTALL FORWARD CLUTCH RETURN SPRING |
 |
Install the piston return spring.
- Place SST on the spring retainer, and compress the return spring with a press.
- SST
- 09350-30020
(09350-07040, 09350-07070)
- NOTICE:
- Be sure the end gap of the snap ring is not aligned with the spring retainer claw.
| 5.
INSTALL FORWARD CLUTCH DISC |
 |
Install the cushion plate.
- for 1KD-FTV:
Install the 6 plates, 6 discs and flange.
- Install in order:
- P - D - P - D - P - D - P - D - P - D - P - D - F
- HINT:
- F = Flange
- P = Plate
- D = Disc
- HINT:
- Only the plate on the bottom is 1.4 mm (0.055 in.) thick. The other plates are 1.8 mm (0.071 in.) thick.
- for 2KD-FTV:
Install the 5 plates, 5 discs and flange.
- Install in order:
- P - D - P - D - P - D - P - D - P - D - F
- HINT:
- F = Flange
- P = Plate
- D = Disc
- HINT:
- Only the plate on the bottom is 1.4 mm (0.055 in.) thick. The other plates are 1.8 mm (0.071 in.) thick.
- Using a screwdriver, install the snap ring.
- NOTICE:
- Be sure the end gap of the snap ring is not aligned with the cutout portion of the forward clutch drum.
| 6.
INSPECT PISTON STROKE OF FORWARD CLUTCH
|
 |
Using SST and a dial indicator, measure the direct clutch piston stroke while applying and releasing compressed air (392 kPa (4.0 kgf/cm2, 57 psi)).
- SST
- 09350-30020
(09350-06120)
- Piston thickness:
- 0.60 to 1.00 mm (0.024 to 0.039 in.)
If the piston stroke is not as specified, parts may have been assembled incorrectly. Check and reassemble again.
- HINT:
- If the piston stroke is still not as specified, select another flange.
- There are 8 different flange thicknesses.
- Piston stroke:
No.
|
Thickness
|
No.
|
Thickness
|
90
|
3.0 mm (0.118 in.)
|
94
|
3.8 mm (0.150 in.)
|
91
|
3.2 mm (0.126 in.)
|
95
|
4.0 mm (0.157 in.)
|
92
|
3.4 mm (0.134 in.)
|
96
|
4.2 mm (0.165 in.)
|
93
|
3.6 mm (0.142 in.)
|
97
|
4.4 mm (0.173 in.)
|