2014 Hilux · Service Manual TRANSMISSION

DISASSEMBLY

Removal / installation · Vehicles built from Jun 2011


1. REMOVE TRANSMISSION CONTROL SHAFT LEVER LH

D027971E01
  1. Remove the nut, washer and control shaft lever LH.


2. REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

D027903E01
  1. Using a screwdriver, pry out the lock washer.

  1. Remove the nut, lock washer and bolt.

  1. Remove the park/neutral position switch.

    HINT:
    Make sure that the manual valve lever shaft has not been rotated prior to installing the park/neutral position switch as the detent spring may become detached from the manual valve lever shaft.


3. REMOVE OIL COOLER TUBE UNION
  1. Remove the 2 oil cooler tube unions.

  1. Remove the O-ring from the oil cooler tube union.


4. REMOVE SPEED SENSOR

C111258
  1. Remove the 2 bolts and 2 transmission revolution sensors.

  1. Remove the O-ring from each sensor.


5. REMOVE AUTOMATIC TRANSAXLE BREATHER TUBE

D027970E02
  1. Remove the 3 bolts.

  1. Remove the breather tube.

  1. Remove the O-ring from each tube.


6. REMOVE AUTOMATIC TRANSMISSION HOUSING

C111207
  1. Remove the 10 bolts.

  1. Remove the transmission housing.


7. REMOVE EXTENSION HOUSING SUB-ASSEMBLY

D027972E01
  1. Remove the 6 bolts.

  1. Remove the extension housing assembly.

    HINT:
    Use a brass bar and hammer to remove the extension housing assembly.

  1. Remove the gasket from the extension housing assembly.

  1. D029874E01
    Using a snap ring expander, remove the snap ring.

  1. Remove the thrust needle roller bearing and 2 bearing races.


8. REMOVE EXTENSION HOUSING DUST DEFLECTOR

D027976E01
  1. Using a brass bar and hammer, remove the extension housing dust deflector.


9. REMOVE AUTOMATIC TRANSMISSION EXTENSION HOUSING OIL SEAL

D027977E01
  1. Using SST, tap out the oil seal.

    SST
    09308-00010  


10. FIX AUTOMATIC TRANSMISSION CASE SUB-ASSEMBLY

D027911E01
  1. Install the transmission case on the overhaul attachment.


11. REMOVE AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

NOTICE:
Do not turn the transmission over as this will contaminate the valve body with foreign matter on the bottom of the pan.

  1. Remove the drain plug and 20 bolts.


12. INSPECT AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

D001124E01
  1. Remove the magnets, and use them to collect steel particles.

  1. Carefully lock at the foreign matter and particles in the pan and on the magnets to anticipate the type of wear you will find in the transmission.

    1. Steel (magnetic): bearing, gear and clutch plate wear
    2. Brass (non-magnetic): bushing wear


13. REMOVE VALVE BODY OIL STRAINER ASSEMBLY

D012703E01
  1. Turn over the transmission.

  1. Remove the 4 bolts holding the valve body oil strainer assembly to the valve body.

  1. Remove the O-ring form the valve body oil strainer assembly.


14. REMOVE TRANSMISSION WIRE

D012704E01
  1. Remove the ATF temperature sensor.

  1. Remove the bolt and clamp.

  1. Disconnect the 7 connectors from the shift solenoid valves.

  1. D027912E01
    Remove the bolt from the case.

  1. Pull the transmission wire out of the transmission case.

  1. Remove the O-ring from the transmission wire.


15. REMOVE TRANSMISSION VALVE BODY ASSEMBLY

D012705E01
  1. Remove the 19 bolts.

  1. Remove the valve body assembly.


16. REMOVE TRANSAXLE CASE GASKET

D027968E03
  1. Remove the 3 transaxle case gaskets.


17. REMOVE BRAKE DRUM GASKET

D027969E01
  1. Remove the 3 brake drum gaskets.


18. REMOVE CHECK BALL BODY

D027914E04
  1. Remove the check ball body and spring.


19. REMOVE C-2 ACCUMULATOR PISTON

D027915E01
  1. Applying compressed air to the oil hole, and remove the C2 accumulator piston and spring.

  1. Remove the 2 O-rings from the piston.

    NOTICE:
    Be careful as the C-3 and B-3 accumulator piston may jump out.


20. REMOVE B-3 ACCUMULATOR PISTON

D027915E01
  1. Applying compressed air to the oil hole, and remove the C2 accumulator piston and spring.

  1. Remove the 2 O-rings from the piston.

    NOTICE:
    Be careful as the C-3 accumulator piston may jump out.


21. REMOVE C-3 ACCUMULATOR PISTON

D027916E01
  1. Applying compressed air to the oil hole, and remove the B-3 accumulator piston and spring.

  1. Remove the 2 O-rings from the piston.


22. REMOVE C-1 ACCUMULATOR VALVE

D027917E01
  1. Remove the C-1 accumulator valve and 2 springs.


23. REMOVE PARKING LOCK PAWL BRACKET

D012708E01
  1. Remove the 3 bolts and parking lock pawl bracket.


24. REMOVE PARKING LOCK ROD SUB-ASSEMBLY

D012709E01
  1. Disconnect the parking lock rod from the manual valve lever.


25. REMOVE PARKING LOCK PAWL SHAFT

D028846E01
  1. Pull out the parking lock pawl shaft from the front side, and then remove the lock pawl and spring.

  1. Remove the E-ring from the shaft.


26. REMOVE MANUAL VALVE LEVER SUB-ASSEMBLY

D027918E01
  1. Using a hammer and screwdriver, cut off the spacer and remove it from the shaft.

  1. D027919E01
    Using a pin punch and hammer, tap out the spring pin.

    HINT:
    Slowly drive out the spring pin so that it does not fall into the transmission case.

  1. Pull the manual valve lever shaft out through the case, and remove the manual valve lever.


27. REMOVE MANUAL VALVE LEVER SHAFT OIL SEAL

D027920E01
  1. Using a screwdriver, remove the 2 oil seals.


28. REMOVE OIL PUMP ASSEMBLY

D027921E01
  1. Remove the 10 bolts holding the oil pump from the transmission case.

  1. D027922E02
    Using SST, remove the oil pump.
    SST
    09350-30020   (09350-07020)

  1. D028809E01
    Remove the No. 1 thrust bearing race from the front oil pump.


29. REMOVE CLUTCH DRUM AND INPUT SHAFT ASSEMBLY

D027923E01
  1. Remove the clutch drum and input shaft drum assembly from the transmission case.

  1. D027924E03
    Remove the clutch drum thrust washer and thrust needle roller bearing.


30. INSPECT 1-WAY NO. 2 CLUTCH ASSEMBLY

D027993E01
  1. Hold the Reverse clutch hub and turn the No. 2 1-way clutch assembly

  1. The No. 2 1-way clutch assembly turns freely clockwise and locks when turned counterclockwise.


31. REMOVE 1-WAY NO. 2 CLUTCH ASSEMBLY

D027994E01
  1. Remove the No. 2 1-way clutch assembly and No. 2 clutch drum thrust washer from the clutch drum and input shaft assembly.


32. REMOVE NO. 3 BRAKE SNAP RING

D027925E01
  1. Using a screwdriver, remove the No. 3 brake snap ring from the case.


33. REMOVE NO. 3 BRAKE DISC

D027926E03
  1. Remove the flange and cushion plate the 4 discs and the 4 plates from the case.


34. INSPECT NO. 3 BRAKE DISC

D001216E01
  1. Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) grooves or printed numbers have even a little bit of damage.

    NOTICE:
    Before assembling new discs, soak them in ATF for at least 15 minutes.


35. REMOVE 2ND BRAKE PISTON HOLE SNAP RING

D027927E03
  1. Using SST, remove the snap ring.

    SST
    09350-30020   (09350-07060)


36. REMOVE 1-WAY CLUTCH ASSEMBLY

D027928E01
  1. Remove the 1-way clutch assembly and the No. 1 planetary carrier thrust washer from the case.


37. REMOVE 2ND BRAKE CYLINDER

D027929E01
  1. Remove the 2nd brake cylinder from the case.


38. REMOVE 2ND BRAKE PISTON

D028817E03
  1. Using SST and a press, remove the snap ring.

    SST
    09351-40010  

  1. D028545E01
    Hold the 2nd brake piston and apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the brake cylinder to remove the 2nd brake piston.

  1. D028546E03
    Remove the 2 O-rings from the 2nd brake piston.


39. INSPECT NO. 3 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

D029828E01
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    15.72 mm (0.619 in.)


40. REMOVE FRONT PLANETARY GEAR ASSEMBLY

D028544E01
  1. Using a feeler gauge, measure the front planetary pinion gear thrust clearance.

    Standard clearance:
    0.2 to 0.60 mm (0.008 to 0.024 in.)
    Maximum clearance:
    0.65 mm (0.026 in.)

    1. If the clearance is greater than the maximum, replace the front planetary gear assembly.

  1. D028543E01
    Using a dial indicator, measure the inside diameter of the front planetary gear bushing.

    Maximum inside diameter:
    57.48 mm (2.263 in.)

    1. If the inside diameter is greater than the maximum, replace the front planetary gear.


41. INSPECT FRONT PLANETARY GEAR ASSEMBLY

D028544E01
  1. Using a feeler gauge, measure the front planetary pinion gear thrust clearance.

    Standard clearance:
    0.2 to 0.60 mm (0.008 to 0.024 in.)
    Maximum clearance:
    0.65 mm (0.026 in.)

    1. If the clearance is greater than the maximum, replace the front planetary gear assembly.

  1. D028543E01
    Using a dial indicator, measure the inside diameter of the front planetary gear bushing.

    Maximum inside diameter:
    57.48 mm (2.263 in.)

    1. If the inside diameter is greater than the maximum, replace the front planetary gear.


42. INSPECT 1-WAY CLUTCH ASSEMBLY

D028542E01
  1. Install the 1-way clutch assembly to the 1-way clutch inner race.

  1. Hold the 1-way clutch inner race and turn the 1-way clutch assembly.

  1. Check that the 1-way clutch assembly turns freely counterclockwise and locks when turned clockwise.

  1. Remove the 1-way clutch assembly from the 1-way clutch inner race.


43. REMOVE FRONT PLANETARY RING GEAR

D027932E01
  1. Remove the front planetary ring gear and bearing from the transmission case.


44. REMOVE CENTER PLANETARY RING GEAR

D028540E01
  1. Using a screwdriver, remove the snap ring.

  1. D028541E01
    Remove the center planetary ring gear and front planetary ring gear flange from the front planetary ring gear.


45. REMOVE NO. 1 BRAKE DISC

D027933E03
  1. Remove the flange, 3 discs and 3 plates from the case.


46. INSPECT NO. 1 BRAKE DISC

D001216E01
  1. Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) grooves or printed numbers have even a little bit of damage.

    NOTICE:
    Before assembling new discs, soak them in ATF for at least 15 minutes.


47. REMOVE BRAKE PISTON RETURN SPRING SNAP RING

D027934E01
  1. Using a screwdriver, remove the brake piston return spring snap ring from the case.


48. REMOVE BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

D027935E01
  1. Remove the brake piston return spring and No. 1 the brake piston with the No. 1 brake cylinder from the transmission case.


49. INSPECT BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

D003830E01
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    17.05 mm (0.671 in.)


50. REMOVE NO. 1 BRAKE PISTON

D027936E01
  1. Hold the brake piston No. 1 and apply compressed air (392 kPa, 4 kgf/cm2, 57 psi) to the transmission case to remove the No. 1 brake piston.

    HINT:
    If the piston does not pop out with compressed air, lift the piston out with needle-nose pliers.

  1. Remove the 2 O-rings from the No. 1 brake piston.


51. REMOVE NO. 2 BRAKE DISC

D027937E01
  1. Using a screwdriver, remove the snap ring from the case.

  1. D027938E03
    Remove the flange, the brake piston return spring, the 3 discs and the 3 plates from the case.


52. INSPECT NO. 2 BRAKE DISC

D001216E01
  1. Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) grooves or printed numbers have even a little bit of damage.

    NOTICE:
    Before assembling new discs, soak them in ATF for at least 15 minutes.


53. INSPECT NO.2 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

D029829E01
  1. Using a vernier calipers, measure the free length of the spring together with the spring seat.

    Standard free length:
    17.45 mm (0.687 in.)


54. REMOVE NO. 2 BRAKE PISTON

D027939E01
  1. Hold the No. 2 brake piston and apply compressed air (392 kPa, 4 kgf/cm2, 57 psi) to the transmission case to remove the No. 2 brake piston.

    HINT:
    If the piston does not pop out with compressed air, lift the piston out with needle-nose pliers.

  1. Remove the 2 O-rings from the No. 2 brake piston.


55. REMOVE CENTER PLANETARY GEAR ASSEMBLY

D027940E01
  1. Remove the center planetary gear assembly, the planetary sun gear and the No. 4 thrust bearing race from the case.


56. INSPECT CENTER PLANETARY GEAR ASSEMBLY

D028533E01
  1. Using a feeler gauge, measure the center planetary gear pinion thrust clearance.

    Standard clearance:
    0.12 to 0.68 mm (0.005 to 0.027 in.)
    Maximum clearance:
    0.73 mm (0.029 in.)

    1. If the clearance is greater than the maximum, replace the center planetary gear assembly.


57. REMOVE INTERMEDIATE SHAFT

D027941E01
  1. Using a screwdriver, remove the snap ring from the case.

  1. D027942E01
    Remove the intermediate shaft with the No. 3 1- way clutch assembly from the case.


58. INSPECT NO. 3 1-WAY CLUTCH ASSEMBLY

D028532E01
  1. Hold the rear planetary ring gear flange sub-assembly turn the 1-way clutch assembly.

  1. Check that the 1-way clutch assembly turns freely counterclockwise and locks when turned clockwise.


59. REMOVE NO. 3 1-WAY CLUTCH ASSEMBLY

D027964E01
  1. Remove the No. 3 1-way clutch assembly and the 1 way clutch inner race from the intermediate shaft.


60. REMOVE REAR PLANETARY RING GEAR FLANGE SUB-ASSEMBLY

D027965E04
  1. Remove the No. 8 thrust bearing race thrust needle roller bearing, the No. 7 thrust bearing race and the planetary ring gear flange from the intermediate shaft.


61. INSPECT REAR PLANETARY RING GEAR FLANGE SUB-ASSEMBLY

D028531E01
  1. Using a dial indicator, measure the inside diameter of the rear planetary ring gear bushing.

    Maximum inside diameter:
    32.175 mm (1.267 in.)

    1. If the inside diameter is greater than the maximum, replace the rear planetary ring gear.


62. INSPECT INTERMEDIATE SHAFT

D028529E01
  1. Using a dial indicator, check the intermediate shaft runout.

    Maximum runout:
    0.08 mm (0.003 in.)

    NOTICE:
    If the bend exceeds the specification, replace the intermediate shaft with anew one.

  1. D028530E02
    Using a micrometer, check the outer diameter of the intermediate shaft positions shown in the diagram.

    Standard diameter:
    A:
    25.962 to 25.975 mm (1.022 to 1.023 in.)
    B:
    25.962 to 25.975 mm (1.022 to 1.023 in.)
    C:
    32.062 to 32.075 mm (1.262 to 1.263 in.)
    D:
    32.062 to 32.075 mm (1.262 to 1.263 in.)

    Standard diameter:
    A:
    25.912 mm (1.020 in.)
    B:
    25.912 mm (1.020in.)
    C:
    32.012 mm (1.260 in.)
    D:
    32.012 mm (1.260 in.)

    NOTICE:
    If the outer diameter is outside the standard, replace the intermediate shaft with the new one.


63. REMOVE BRAKE PLATE STOPPER SPRING

D027943E01
  1. Remove the brake plate stopper spring from the case.


64. REMOVE NO. 4 BRAKE DISC

D027944E03
  1. Remove the 7 plates, the 8 discs and the 2 flanges from the case.


65. INSPECT NO. 4 BRAKE DISC

D001216E01
  1. Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) grooves or printed numbers have even a little bit of damage.

    NOTICE:
    Before assembling new discs, soak them in ATF for at least 15 minutes.


66. REMOVE REAR PLANETARY GEAR ASSEMBLY

D027945E01
  1. Remove the rear planetary gear assembly from the case.

  1. D027946E02
    Remove the thrust bearing race No. 9 and the thrust needle roller bearing from the rear planetary gear assembly.

  1. D027947E01
    Remove the thrust needle roller bearing from the case.


67. INSPECT REAR PLANETARY GEAR ASSEMBLY

D028531E01
  1. Using a dial indicator, measure the inside diameter of the rear planetary ring gear bushing.

    Maximum inside diameter:
    32.175 mm (1.267 in.)

    1. If the inside diameter is greater than the maximum, replace the rear planetary ring gear.


68. REMOVE 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

D028083E01
  1. Place SST on the spring retainer and compress the brake return spring.

    SST
    09350-30020   (09350-07050)

  1. Using SST, remove the snap ring and the brake return spring.

    SST
    09350-30020   (09350-07070)


69. INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

D029830E01
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    23.74 mm (0.935 in.)


70. REMOVE 1ST AND REVERSE BRAKE PISTON

D027948E01
  1. Hold the No. 2 brake piston and apply compressed air (392 kPa, 4 kgf/cm2, 57 psi) to the transmission case to remove the No. 2 brake piston.

    HINT:
    If the piston does not pop out with compressed air, lift the piston out with needle-nose pliers.

  1. Remove the O-ring from No. 2 brake piston.


71. REMOVE BRAKE REACTION SLEEVE

D028079E04
  1. Using SST, remove the reaction sleeve.

    SST
    09350-30020   (09350-07080)

  1. Remove the O-ring from the reaction sleeve.


72. REMOVE NO. 4 BRAKE PISTON

D001240E03
  1. Using SST, remove the No. 4 bbrake piston.

    SST
    09350-30020   (09350-07090)

  1. Remove the 2 O-rings from the No. 4 piston.

← COMPONENTS (from Jun 2011)INSPECTION (from Jun 2011) →