TERMINALS OF ECM
System information · Vehicles built from Jun 2011


- HINT:
- Each ECM terminal's standard voltage is shown in the table below.
- In the table, first follow the information under "Condition". Look under "Terminal No. (Symbol)" for the terminals to be inspected. The standard voltage between the terminals is shown under "Specified Condition".
- Use the illustration above as a reference for the ECM terminals.
| Terminal No. (Symbol) |
Wiring Color |
Terminal Description |
Condition |
Specified Condition |
| E31-23 (BATT) - E25-1 (E1) |
L - BR |
Battery (for measuring the battery voltage and for the ECM memory) |
Always |
11 to 14 V |
| E30-24 (IGSW) - E25-1 (E1) |
B-O - BR |
Ignition switch |
Ignition switch ON |
11 to 14 V |
| E31-24 (+B) - E25-1 (E1) |
B - BR |
Power source of ECM |
Ignition switch ON |
11 to 14 V |
| E31-17 (+B2) - E25-1 (E1) |
B-R - BR |
Power source of ECM |
Ignition switch ON |
11 to 14 V |
| E30-11 (MREL) - E25-1 (E1) |
W-G - BR |
EFI relay |
Ignition switch ON |
11 to 14 V |
| E30-11 (MREL) - E25-1 (E1) |
W-G - BR |
EFI relay |
10 seconds elapsed after ignition switch off |
0 to 1.5 V |
| E30-6 (VCPA) - E30-5 (EPA) |
LG-R - BR-W |
Power source of accelerator pedal position sensor (for VPA) |
Ignition switch ON |
4.5 to 5.5 V |
| E30-4 (VCP2) - E30-3 (EPA2) |
BR-R - BR-Y |
Power source of accelerator pedal position sensor (for VPA2) |
Ignition switch ON |
4.5 to 5.5 V |
| E31-2 (VPA) - E30-5 (EPA) |
W-L - BR-W |
Accelerator pedal position sensor (for engine control) |
Ignition switch ON, accelerator pedal fully released |
0.5 to 1.1 V |
| E31-2 (VPA) - E30-5 (EPA) |
W-L - BR-W |
Accelerator pedal position sensor (for engine control) |
Ignition switch ON, accelerator pedal fully depressed |
3.0 to 4.6 V |
| E31-1 (VPA2) - E30-3 (EPA2) |
GR-G - BR-Y |
Accelerator pedal position sensor (for sensor malfunction detection) |
Ignition switch ON, accelerator pedal fully released |
0.9 to 2.3 V |
| E31-1 (VPA2) - E30-3 (EPA2) |
GR-G - BR-Y |
Accelerator pedal position sensor (for sensor malfunction detection) |
Ignition switch ON, accelerator pedal fully depressed |
3.4 to 5.0 V |
| E27-13 (VC) - E27-14 (E2) |
R-W - BR |
Power source for sensor (specific voltage) |
Engine switch on (IG) |
4.5 to 5.0 V |
| E26-17 (VG) - E26-18 (EVG) |
W-R - B-W |
Mass air flow meter |
Idling |
Pulse generation |
| E26-6 (THA) - E27-14 (E2) |
Y-B - BR |
Intake air temperature sensor (built into mass air flow meter) |
Idling, intake air temperature at 20°C (68°F) |
0.5 to 3.4 V |
| E26-3 (THIA) - E27-14 (E2) |
Y-G - BR |
Intake air temperature sensor |
Idling, intake air temperature at 0 to 80°C (32 to 176°F) |
0.5 to 3.4 V |
| E26-5 (THW) - E27-14 (E2) |
R-L - BR |
Engine coolant temperature sensor |
Idling, engine coolant temperature at 80°C (176°F) |
0.2 to 1.0 V |
| E26-4 (THF) - E27-14 (E2) |
G-B - BR |
Fuel temperature sensor |
Ignition switch ON |
0.5 to 3.4 V |
| E31-6 (STA) - E25-1 (E1) |
L-Y - BR*1 B-Y - BR*2 |
Starter signal |
Cranking |
6.0 V or higher |
| E26-21 (#1) - E25-1 (E1) E26-22 (#2) - E25-1 (E1) E26-23 (#3) - E25-1 (E1) E26-24 (#4) - E25-1 (E1) |
B-W - BR R - BR V - BR Y-R - BR |
Injector assembly |
Idling |
Pulse generation (See waveform 2) |
| E24-13 (G+) - E24-14 (G-) |
Y - L |
Camshaft position sensor |
Idling |
Pulse generation (See waveform 5) |
| E24-7 (NE+) - E24-8 (NE-) |
Y - L |
Crankshaft position sensor |
Idling |
Pulse generation (See waveform 5) |
| E31-8 (STP) - E25-1 (E1) |
G-W - BR |
Stop light switch assembly |
Ignition switch ON, brake pedal depressed |
7.5 to 14 V |
| E31-8 (STP) - E25-1 (E1) |
G-W - BR |
Stop light switch assembly |
Ignition switch ON, brake pedal released |
0 to 1.5 V |
| E31-9 (ST1-) - E25-1 (E1) |
R-L - BR |
Stop light switch assembly (opposite to STP) |
Ignition switch ON, brake pedal depressed |
0 to 1.5 V |
| E31-9 (ST1-) - E25-1 (E1) |
R-L - BR |
Stop light switch assembly (opposite to STP) |
Ignition switch ON, brake pedal released |
7.5 to 14 V |
| E27-15 (CLSW)*1 - E25-1 (E1) |
G-W - BR |
Clutch switch assembly |
Ignition switch ON, clutch pedal released |
8.5 to 14 V |
| E30-23 (TC) - E25-1 (E1) |
P-B - BR |
Terminal TC of DLC3 |
Ignition switch ON |
11 to 14 V |
| E31-19 (W) - E25-1 (E1) |
R-B - BR |
MIL |
MIL illuminated |
0 to 3 V |
| E31-19 (W) - E25-1 (E1) |
R-B - BR |
MIL |
MIL not illuminated |
11 to 14 V |
| E30-30 (SPD) - E25-1 (E1) |
V-R - BR |
Speed signal from combination meter assembly |
Ignition switch ON, slowly wheel rotated |
Pulse generation (See waveform 9) |
| E27-5 (PIM) - E27-14 (E2) |
L-B - BR |
Manifold absolute pressure sensor |
Negative pressure of 40 kPa (300 mmHg, 11.8 in.Hg) applied |
0.1 to 0.7 V |
| E27-5 (PIM) - E27-14 (E2) |
L-B - BR |
Manifold absolute pressure sensor |
Same as atmospheric pressure |
0.8 to 1.5 V |
| E27-5 (PIM) - E27-14 (E2) |
L-B - BR |
Manifold absolute pressure sensor |
Positive pressure of 170 kPa (1275 mmHg, 50.2 in.Hg) applied |
1.6 to 2.3 V |
| E30-12 (IREL) - E25-1 (E1) |
B-W - BR |
EDU relay |
Ignition switch ON |
0 to 1.5 V |
| E31-18 (TACH) - E25-1 (E1) |
B-W - BR |
Engine speed |
Idling |
Pulse generation |
| E26-13 (VCS) - E26-8 (E2S) |
L-W - P-L |
Power source of fuel pressure sensor (for PCR2) |
Ignition switch ON |
4.5 to 5.5 V |
| E26-16 (PCR1) - E27-14 (E2) |
R-Y - BR |
Fuel pressure sensor (main) |
Idling |
1.8 to 2.1 V |
| E26-2 (PCR2) - E26-8 (E2S) |
G-R - P-L |
Fuel pressure sensor (sub) |
Idling |
1.2 to 1.5 V |
| E27-23 (ALT) - E25-1 (E1) |
G - BR |
Generator assembly (Alternator) duty ratio |
Idling |
Pulse generation |
| E27-7 (PEX) - E27-14 (E2) |
L - BR |
Differential pressure sensor |
Ignition switch ON |
0.4 to 4.8 V |
| E24-6 (HAF2) - E25-11 (E05) |
Y - W-B |
Air fuel ratio sensor heater |
Ignition switch ON |
11 to 14 V |
| E24-2 (AF2+) - E25-11 (E05) |
B - W-B |
Air fuel ratio sensor |
Ignition switch ON |
2.0 to 2.5 V |
| E24-1 (AF2-) - E25-11 (E05) |
W - W-B |
Air fuel ratio sensor |
Ignition switch ON |
2.0 to 2.5 V |
| E25-5 (FIV) - E25-1 (E1) |
W - BR |
Exhaust fuel addition injector |
Exhaust fuel addition injector operating |
Pulse generation |
| E24-23 (PCV+) - E24-12 (PCV-) |
G-W - G-Y |
Suction control valve |
Idling |
Pulse generation (See waveform 1) |
| E26-20 (INJF) - E25-1 (E1) |
P - BR |
Injector driver |
Idling |
Pulse generation (See waveform 3) |
| E26-19 (PRD) - E25-1 (E1) |
GR - BR |
Pressure discharge valve drive signal |
Engine warmed up, engine racing |
Pulse generation (See waveform 4) |
| E24-4 (RLFF) - E25-1 (E1) |
GR - BR |
Pressure discharge valve confirmation signal |
Engine warmed up, engine racing |
Pulse generation (See waveform 4) |
| E24-19 (IDLO) - E25-1 (E1) |
G - BR |
EDU |
Idling |
4 to 5.5 V |
| E25-15 (M+) - E25-1 (E1) |
W - BR |
DC motor (turbocharger sub-assembly) |
Idling |
Pulse generation (See waveform 6) |
| E25-14 (M-) - E25-1 (E1) |
B - BR |
DC motor (turbocharger sub-assembly) |
Idling |
Pulse generation (See waveform 7) |
| E27-11 (VNVC) - E27-10 (VNE2) |
W - L |
Power source of nozzle vane position sensor |
Ignition switch ON |
4.5 to 5.5 V |
| E27-6 (VNA) - E27-10 (VNE2) |
R - L |
Nozzle vane position sensor |
Ignition switch ON |
2.3 to 2.7 V |
| E27-3 (VLU) - E27-14 (E2) |
B- BR |
Throttle position sensor |
Ignition switch ON, throttle valve fully opened |
3.6 to 4.2 V |
| E27-3 (VLU) - E27-14 (E2) |
B- BR |
Throttle position sensor |
Ignition switch ON, throttle valve fully closed |
0.4 to 1.0 V |
| E24-15 (LUSL) - E25-1 (E1) |
GR - BR |
Diesel throttle duty signal |
Engine warmed up, racing engine |
Pulse generation (See waveform 8) |
| E26-1 (EGRA) - E27-14 (E2) |
R-Y - BR |
EGR valve position sensor |
Ignition switch ON |
0.6 to 1.4 V |
| E25-6 (EGM+) - E25-8 (ME01) |
L - W-B |
EGR valve duty signal |
Engine warmed up, idling |
Pulse generation |
| E25-7 (EGM-) - E25-8 (ME01) |
Y - W-B |
EGR valve duty signal |
Engine warmed up, idling |
Pulse generation |
| E25-4 (ECBV) - E25-1 (E1) |
B-L - BR |
Vacuum switching valve (for EGR bypass valve) |
Vacuum switching valve assembly (for EGR bypass valve) on |
0 to 1.5 V |
| Vacuum switching valve assembly (for EGR bypass valve) off |
11 to 14 V |
|||
| E24-17 (THCF) - E27-14 (E2) |
R - BR |
Exhaust gas temperature sensor |
Engine warmed up, idling |
4.6 to 4.9 V |
| E24-5 (THCI) - E27-14 (E2) |
G-B - BR |
No. 2 Exhaust gas temperature sensor |
Engine warmed up, idling |
4.6 to 4.9 V |
| E27-1 (THCO) - E27-14 (E2) |
B-Y - BR |
No. 3 Exhaust gas temperature sensor |
Engine warmed up, idling |
4.6 to 4.9 V |
| E25-2 (SCV) - E25-12 (E01) |
LG - W-B |
Vacuum switching valve (for swirl control valve) |
Idling |
0 to 1.5 V |
| Engine speed 2600 rpm or more |
11 to 14 V |
|||
| E30-10 (AC1) - E25-12 (E01) |
Y - W-B |
A/C signal |
A/C switch on |
0 to 1.5 V |
| A/C switch off |
11 to 14 V |
|||
| E30-13 (ACT) - E25-12 (E01) |
R-L - W-B |
A/C signal |
Ignition switch ON |
11 to 14 V |
| A/C cut control on |
0 to 3 V |
|||
| E24-26 (NSW)*2 - E25-12 (E01) |
L-Y - W-B |
Park/neutral position switch assembly |
Ignition switch ON, shift lever in P or N |
Below 3 V |
| Ignition switch ON, shift lever not in P and N |
11 to 14 V |
|||
| E27-15 (D)*2 - E25-12 (E01) |
G-Y - W-B |
Park/neutral position switch assembly |
Ignition switch ON, shift lever in D |
11 to 14 V |
| Ignition switch ON, shift lever not in D |
Below 1 V |
|||
| E30-36 (CANL) - E25-1 (E1) |
W - BR |
CAN communication line |
Ignition switch ON |
Pulse generation (See waveform 10) |
| E30-35 (CANH) - E25-1 (E1) |
B - BR |
CAN communication line |
Ignition switch ON |
Pulse generation (See waveform 11) |
| E24-18 (CAN-)*2 - E25-1 (E1) |
P - BR |
CAN communication line |
Ignition switch ON |
Pulse generation (See waveform 10) |
| E24-24 (CAN+)*2 - E25-1 (E1) |
V - BR |
CAN communication line |
Ignition switch ON |
Pulse generation (See waveform 11) |
- HINT:
- *1: for Manual Transaxle
- *2: for Automatic Transaxle
- *1: for Manual Transaxle
| WAVEFORM 1 |
![]() ![]() |
| Item |
Content |
| Terminal No. (Symbol) |
E24-23 (PCV+) - E24-12 (PCV-) |
| Tool Setting |
10 V/DIV., 5 msec./DIV. |
| Condition |
Idling or cranking with warm engine |
- HINT:
- The waveform varies depending on suction control valve operation.
| WAVEFORM 2 |
![]() ![]() |
| Item |
Content |
| Terminal No. (Symbol) |
(a) E26-21 (#1) - E25-1 (E1) (b) E26-22 (#2) - E25-1 (E1) (c) E26-23 (#3) - E25-1 (E1) (d) E26-24 (#4) - E25-1 (E1) |
| Tool Setting |
5 V/DIV., 20 msec./DIV. |
| Condition |
Idling with warm engine |
- HINT:
- The waveform varies depending on the injector injection.
| WAVEFORM 3 |
![]() ![]() |
| Item |
Content |
| Terminal No. (Symbol) |
E26-20 (INJF) - E25-1 (E1) |
| Tool Setting |
2 V/DIV., 20 msec./DIV. |
| Condition |
Idling with warm engine |
- HINT:
- The waveform varies depending on the injector injection.
| WAVEFORM 4 |
![]() ![]() |
| Item |
Content |
| Terminal No. (Symbol) |
(a) E26-19 (PRD) - E25-1 (E1) (b) E24-4 (RLFF) - E25-1 (E1) |
| Tool Setting |
2 V/DIV., 1 msec./DIV. |
| Condition |
Engine warmed up, engine racing |
- HINT:
- The waveform becomes shorter as the engine speed.
| WAVEFORM 5 |
![]() ![]() |
| Item |
Content |
| Terminal No. (Symbol) |
(a) E24-7 (NE+) - E24-8 (NE-) (b) E24-13 (G+) - E24-14 (G-) |
| Tool Setting |
5 V/DIV., 20 msec./DIV. |
| Condition |
Idling with warm engine |
- HINT:
- The waveform varies depending on the engine speed.
| WAVEFORM 6 |
![]() ![]() |
| Item |
Content |
| Terminal No. (Symbol) |
E25-15 (M+) - E25-1 (E1) |
| Tool Setting |
5 V/DIV., 20 msec./DIV. |
| Condition |
Idling with warm engine |
- HINT:
- The waveform varies depending on turbocharger operation.
| WAVEFORM 7 |
![]() ![]() |
| Item |
Content |
| Terminal No. (Symbol) |
E25-14 (M-) - E25-1 (E1) |
| Tool Setting |
5 V/DIV., 50 msec./DIV. |
| Condition |
Idling with warm engine |
- HINT:
- The waveform varies depending on the turbocharger status.
| WAVEFORM 8 |
![]() ![]() |
| Item |
Content |
| Terminal No. (Symbol) |
E24-15 (LUSL) - E25-1 (E1) |
| Tool Setting |
1 V/DIV., 2 msec./DIV. |
| Condition |
Racing with warm engine |
- HINT:
- The waveform varies depending on throttle valve operation.
| WAVEFORM 9 |
![]() ![]() |
| Item |
Content |
| Terminal No. (Symbol) |
E30-30 (SPD) - E25-1 (E1) |
| Tool Setting |
5 V/DIV., 10 msec./DIV. |
| Condition |
Driving at vehicle speed of 40 km/h (25 mph) |
- HINT:
- The wavelength becomes shorter as the vehicle speed increases.
| WAVEFORM 10 |
![]() ![]() |
| Item |
Content |
| Terminal No. (Symbol) |
E30-36 (CANL) - E25-1 (E1) E24-18 (CAN-) - E25-1 (E1) |
| Tool Setting |
1 V/DIV., 10 msec./DIV. |
| Condition |
Engine stopped, ignition switch ON |
- HINT:
- The waveform varies depending on the CAN communication signal.
| WAVEFORM 11 |
![]() ![]() |
| Item |
Content |
| Terminal No. (Symbol) |
E30-35 (CANH) - E25-1 (E1) E24-24 (CAN+) - E25-1 (E1) |
| Tool Setting |
1 V/DIV., 10 msec./DIV. |
| Condition |
Engine stopped, ignition switch ON |
- HINT:
- The waveform varies depending on the CAN communication signal.










