Terminal No. (Symbol)
|
Wiring Color
|
Terminal Description
|
Condition
|
Specified Condition
|
E31-23 (BATT) - E25-1 (E1)
|
L - BR
|
Battery (for measuring the battery voltage and for the ECM memory)
|
Always
|
11 to 14 V
|
E30-24 (IGSW) - E25-1 (E1)
|
B-O - BR
|
Ignition switch
|
Ignition switch ON
|
11 to 14 V
|
E31-24 (+B) - E25-1 (E1)
|
B - BR
|
Power source of ECM
|
Ignition switch ON
|
11 to 14 V
|
E31-17 (+B2) - E25-1 (E1)
|
B-R - BR
|
Power source of ECM
|
Ignition switch ON
|
11 to 14 V
|
E30-11 (MREL) - E25-1 (E1)
|
W-G - BR
|
EFI relay
|
Ignition switch ON
|
11 to 14 V
|
E30-11 (MREL) - E25-1 (E1)
|
W-G - BR
|
EFI relay
|
10 seconds elapsed after ignition switch off
|
0 to 1.5 V
|
E30-6 (VCPA) - E30-5 (EPA)
|
LG-R - BR-W
|
Power source of accelerator pedal position sensor (for VPA)
|
Ignition switch ON
|
4.5 to 5.5 V
|
E30-4 (VCP2) - E30-3 (EPA2)
|
BR-R - BR-Y
|
Power source of accelerator pedal position sensor (for VPA2)
|
Ignition switch ON
|
4.5 to 5.5 V
|
E31-2 (VPA) - E30-5 (EPA)
|
W-L - BR-W
|
Accelerator pedal position sensor (for engine control)
|
Ignition switch ON, accelerator pedal fully released
|
0.5 to 1.1 V
|
E31-2 (VPA) - E30-5 (EPA)
|
W-L - BR-W
|
Accelerator pedal position sensor (for engine control)
|
Ignition switch ON, accelerator pedal fully depressed
|
3.0 to 4.6 V
|
E31-1 (VPA2) - E30-3 (EPA2)
|
GR-G - BR-Y
|
Accelerator pedal position sensor (for sensor malfunction detection)
|
Ignition switch ON, accelerator pedal fully released
|
0.9 to 2.3 V
|
E31-1 (VPA2) - E30-3 (EPA2)
|
GR-G - BR-Y
|
Accelerator pedal position sensor (for sensor malfunction detection)
|
Ignition switch ON, accelerator pedal fully depressed
|
3.4 to 5.0 V
|
E27-13 (VC) - E27-14 (E2)
|
R-W - BR
|
Power source for sensor (specific voltage)
|
Engine switch on (IG)
|
4.5 to 5.0 V
|
E26-17 (VG) - E26-18 (EVG)
|
W-R - B-W
|
Mass air flow meter
|
Idling
|
Pulse generation
|
E26-6 (THA) - E27-14 (E2)
|
Y-B - BR
|
Intake air temperature sensor (built into mass air flow meter)
|
Idling, intake air temperature at 20°C (68°F)
|
0.5 to 3.4 V
|
E26-3 (THIA) - E27-14 (E2)
|
Y-G - BR
|
Intake air temperature sensor
|
Idling, intake air temperature at 0 to 80°C (32 to 176°F)
|
0.5 to 3.4 V
|
E26-5 (THW) - E27-14 (E2)
|
R-L - BR
|
Engine coolant temperature sensor
|
Idling, engine coolant temperature at 80°C (176°F)
|
0.2 to 1.0 V
|
E26-4 (THF) - E27-14 (E2)
|
G-B - BR
|
Fuel temperature sensor
|
Ignition switch ON
|
0.5 to 3.4 V
|
E31-6 (STA) - E25-1 (E1)
|
L-Y - BR
|
Starter signal
|
Cranking
|
6.0 V or higher
|
E26-21 (#1) - E25-1 (E1) E26-22 (#2) - E25-1 (E1) E26-23 (#3) - E25-1 (E1) E26-24 (#4) - E25-1 (E1)
|
B-W - BR R - BR V - BR Y-R - BR
|
Injector assembly
|
Idling
|
Pulse generation (See waveform 2)
|
E24-13 (G+) - E24-14 (G-)
|
Y - L
|
Camshaft position sensor
|
Idling
|
Pulse generation (See waveform 5)
|
E24-7 (NE+) - E24-8 (NE-)
|
Y - L
|
Crankshaft position sensor
|
Idling
|
Pulse generation (See waveform 5)
|
E31-8 (STP) - E25-1 (E1)
|
G-W - BR
|
Stop light switch assembly
|
Ignition switch ON, brake pedal depressed
|
7.5 to 14 V
|
E31-8 (STP) - E25-1 (E1)
|
G-W - BR
|
Stop light switch assembly
|
Ignition switch ON, brake pedal released
|
0 to 1.5 V
|
E31-9 (ST1-) - E25-1 (E1)
|
R-L - BR
|
Stop light switch assembly (opposite to STP)
|
Ignition switch ON, brake pedal depressed
|
0 to 1.5 V
|
E31-9 (ST1-) - E25-1 (E1)
|
R-L - BR
|
Stop light switch assembly (opposite to STP)
|
Ignition switch ON, brake pedal released
|
7.5 to 14 V
|
E27-15 (CLSW) - E25-1 (E1)
|
G-W - BR
|
Clutch switch assembly
|
Ignition switch ON, clutch pedal released
|
8.5 to 14 V
|
E30-23 (TC) - E25-1 (E1)
|
P-B - BR
|
Terminal TC of DLC3
|
Ignition switch ON
|
11 to 14 V
|
E31-19 (W) - E25-1 (E1)
|
R-B - BR
|
MIL
|
MIL illuminated
|
0 to 3 V
|
E31-19 (W) - E25-1 (E1)
|
R-B - BR
|
MIL
|
MIL not illuminated
|
11 to 14 V
|
E30-30 (SPD) - E25-1 (E1)
|
V-R - BR
|
Speed signal from combination meter assembly
|
Ignition switch ON, slowly wheel rotated
|
Pulse generation (See waveform 9)
|
E27-5 (PIM) - E27-14 (E2)
|
L-B - BR
|
Manifold absolute pressure sensor
|
Negative pressure of 40 kPa (300 mmHg, 11.8 in.Hg) applied
|
0.1 to 0.7 V
|
E27-5 (PIM) - E27-14 (E2)
|
L-B - BR
|
Manifold absolute pressure sensor
|
Same as atmospheric pressure
|
0.8 to 1.5 V
|
E27-5 (PIM) - E27-14 (E2)
|
L-B - BR
|
Manifold absolute pressure sensor
|
Positive pressure of 170 kPa (1275 mmHg, 50.2 in.Hg) applied
|
1.6 to 2.3 V
|
E30-12 (IREL) - E25-1 (E1)
|
B-W - BR
|
EDU relay
|
Ignition switch ON
|
0 to 1.5 V
|
E31-18 (TACH) - E25-1 (E1)
|
B-W - BR
|
Engine speed
|
Idling
|
Pulse generation
|
E26-13 (VCS) - E26-8 (E2S)
|
L-W - P-L
|
Power source of fuel pressure sensor (for PCR2)
|
Ignition switch ON
|
4.5 to 5.5 V
|
E26-16 (PCR1) - E27-14 (E2)
|
R-Y - BR
|
Fuel pressure sensor (main)
|
Idling
|
1.8 to 2.1 V
|
E26-2 (PCR2) - E26-8 (E2S)
|
G-R - P-L
|
Fuel pressure sensor (sub)
|
Idling
|
1.2 to 1.5 V
|
E27-23 (ALT) - E25-1 (E1)
|
G - BR
|
Generator assembly (Alternator) duty ratio
|
Idling
|
Pulse generation
|
E27-7 (PEX) - E27-14 (E2)
|
L - BR
|
Differential pressure sensor
|
Ignition switch ON
|
0.4 to 4.8 V
|
E24-6 (HAF2) - E25-11 (E05)
|
Y - W-B
|
Air fuel ratio sensor heater
|
Ignition switch ON
|
11 to 14 V
|
E24-2 (AF2+) - E25-11 (E05)
|
B - W-B
|
Air fuel ratio sensor
|
Ignition switch ON
|
2.0 to 2.5 V
|
E24-1 (AF2-) - E25-11 (E05)
|
W - W-B
|
Air fuel ratio sensor
|
Ignition switch ON
|
2.0 to 2.5 V
|
E25-5 (FIV) - E25-1 (E1)
|
W - BR
|
Exhaust fuel addition injector
|
Exhaust fuel addition injector operating
|
Pulse generation
|
E24-23 (PCV+) - E24-12 (PCV-)
|
G-W - G-Y
|
Suction control valve
|
Idling
|
Pulse generation (See waveform 1)
|
E26-20 (INJF) - E25-1 (E1)
|
P - BR
|
Injector driver
|
Idling
|
Pulse generation (See waveform 3)
|
E26-19 (PRD) - E25-1 (E1)
|
GR - BR
|
Pressure discharge valve drive signal
|
Engine warmed up, engine racing
|
Pulse generation (See waveform 4)
|
E24-4 (RLEF) - E25-1 (E1)
|
GR - BR
|
Pressure discharge valve confirmation signal
|
Engine warmed up, engine racing
|
Pulse generation (See waveform 4)
|
E24-19 (IDLO) - E25-1 (E1)
|
G - BR
|
EDU
|
Idling
|
4 to 5.5 V
|
E25-15 (M+) - E25-1 (E1)
|
W - BR
|
DC motor (turbocharger sub-assembly)
|
Idling
|
Pulse generation (See waveform 6)
|
E25-14 (M-) - E25-1 (E1)
|
B - BR
|
DC motor (turbocharger sub-assembly)
|
Idling
|
Pulse generation (See waveform 7)
|
E27-11 (VNVC) - E27-10 (VNE2)
|
W - L
|
Power source of nozzle vane position sensor
|
Ignition switch ON
|
4.5 to 5.5 V
|
E27-6 (VNA) - E27-10 (VNE2)
|
R - L
|
Nozzle vane position sensor
|
Ignition switch ON
|
2.3 to 2.7 V
|
E27-3 (VLU) - E27-14 (E2)
|
B- BR
|
Throttle position sensor
|
Ignition switch ON, throttle valve fully opened
|
3.6 to 4.2 V
|
E27-3 (VLU) - E27-14 (E2)
|
B- BR
|
Throttle position sensor
|
Ignition switch ON, throttle valve fully closed
|
0.4 to 1.0 V
|
E24-15 (LUSL) - E25-1 (E1)
|
GR - BR
|
Diesel throttle duty signal
|
Engine warmed up, racing engine
|
Pulse generation (See waveform 8)
|
E26-1 (EGRA) - E27-14 (E2)
|
R-Y - BR
|
EGR valve position sensor
|
Ignition switch ON
|
0.6 to 1.4 V
|
E25-6 (EGM+) - E25-8 (ME01)
|
L - W-B
|
EGR valve duty signal
|
Engine warmed up, idling
|
Pulse generation
|
E25-7 (EGM-) - E25-8 (ME01)
|
Y - W-B
|
EGR valve duty signal
|
Engine warmed up, idling
|
Pulse generation
|
E25-4 (ECBV) - E25-1 (E1)
|
B-L - BR
|
Vacuum switching valve (for EGR bypass valve)
|
Vacuum switching valve assembly (for EGR bypass valve) on
|
0 to 1.5 V
|
Vacuum switching valve assembly (for EGR bypass valve) off
|
11 to 14 V
|
E24-17 (THCF) - E27-14 (E2)
|
R - BR
|
Exhaust gas temperature sensor
|
Engine warmed up, idling
|
4.6 to 4.9 V
|
E24-5 (THCI) - E27-14 (E2)
|
G-B - BR
|
No. 2 Exhaust gas temperature sensor
|
Engine warmed up, idling
|
4.6 to 4.9 V
|
E27-1 (THCO) - E27-14 (E2)
|
B-Y - BR
|
No. 3 Exhaust gas temperature sensor
|
Engine warmed up, idling
|
4.6 to 4.9 V
|
E30-10 (AC1) - E25-12 (E01)
|
Y - W-B
|
A/C signal
|
A/C switch on
|
0 to 1.5 V
|
A/C switch off
|
11 to 14 V
|
E30-13 (ACT) - E25-12 (E01)
|
R-L - W-B
|
A/C signal
|
Ignition switch ON
|
11 to 14 V
|
A/C cut control on
|
0 to 3 V
|
E30-36 (CANL) - E25-1 (E1)
|
W - BR
|
CAN communication line
|
Ignition switch ON
|
Pulse generation (See waveform 10)
|
E30-35 (CANH) - E25-1 (E1)
|
B - BR
|
CAN communication line
|
Ignition switch ON
|
Pulse generation (See waveform 11)
|