Symbols (Terminal No.)
|
Wiring Color
|
Terminal Description
|
Condition
|
Specified Condition
|
BATT (E6-2) - E1 (E7-7)
|
L - BR
|
Battery (for measuring the battery voltage and for the ECM memory)
|
Always
|
11 to 14 V
|
IGSW (E5-9) - E1 (E7-7)
|
B-O - BR
|
Ignition switch
|
Ignition switch ON
|
11 to 14 V
|
+B (E5-1) - E1 (E7-7)
|
B - BR
|
Power source of ECM
|
Ignition switch ON
|
11 to 14 V
|
MREL (E5-8) - E1 (E7-7)
|
W-G - BR
|
MAIN relay
|
Ignition switch ON
|
11 to 14 V
|
10 seconds elapsed after ignition switch OFF
|
0 to 1.5 V
|
VC (E8-18) - E2 (E8-28)
|
R-W - BR
|
Power source of sensor (specific voltage)
|
Ignition switch ON
|
4.5 to 5.5 V
|
VCS (E7-2) - E2S (E7-1)
|
L-W - P-L
|
Power source of fuel pressure sensor (sub)
|
Ignition switch ON
|
4.5 to 5.5 V
|
VPA (E5-22) - EPA (E5-28)
|
W-L - BR-W
|
Accelerator pedal position sensor (for engine control)
|
Ignition switch ON, accelerator pedal fully released
|
0.6 to 1.0 V
|
Ignition switch ON, accelerator pedal fully depressed
|
3.0 to 4.6 V
|
VPA2 (E5-23) - EPA2 (E5-29)
|
GR-G - BR-Y
|
Accelerator pedal position sensor (for sensor malfunction detection)
|
Ignition switch ON, accelerator pedal fully released
|
1.4 to 1.8 V
|
Ignition switch ON, accelerator pedal fully depressed
|
3.7 to 5.0 V
|
VCPA (E5-26) - EPA (E5-28)
|
LG-R - BR-W
|
Power source of accelerator pedal position sensor (for VPA)
|
Ignition switch ON
|
4.5 to 5.0 V
|
VCP2 (E5-27) - EPA2 (E5-29)
|
BR-R - BR-Y
|
Power source of accelerator pedal position sensor (for VPA2)
|
Ignition switch ON
|
4.5 to 5.0 V
|
VG (E7-24) - EVG (E7-32)
|
W-R - B-W
|
MAF meter
|
Idling, A/C switch OFF
|
0.5 to 3.4 V
|
THA (E8-31) - E2 (E8-28)
|
Y-B*3 - BR Y-G*4 - BR
|
IAT sensor (built into MAF meter*3)
|
Idling, intake air temperature at 20°C (68°F)
|
0.5 to 3.4 V
|
THIA (E8-20)*5 - E2 (E8-28)
|
Y-G - BR
|
Intake air temperature sensor (turbo)
|
Atmospheric air temperature
|
0.5 to 3.4 V
|
THW (E8-19) - E2 (E8-28)
|
R-L - BR
|
ECT sensor
|
Idling, engine coolant temperature at 80°C (176°F)
|
0.2 to 1.0 V
|
STA (E5-7) - E1 (E7-7)
|
B-Y*1 - BR L-Y*2 - BR
|
Starter signal
|
Cranking
|
6.0 V or more
|
#1 (E8-24) - E1 (E7-7) #2 (E8-23) - E1 (E7-7) #3 (E8-22) - E1 (E7-7) #4 (E8-21) - E1 (E7-7)
|
B-W - BR R - BR V - BR Y-R - BR
|
Injector
|
Idling
|
Pulse generation (see waveform 1)
|
NE+ (E8-27) - NE- (E8-34)
|
Y - L
|
Crankshaft position sensor
|
Idling
|
Pulse generation (see waveform 2)
|
G+ (E7-23) - G- (E7-31)
|
Y - L
|
Camshaft position sensor
|
Idling
|
Pulse generation (see waveform 2)
|
STP (E6-15) - E1 (E7-7)
|
G-W - BR
|
Stop light switch
|
Ignition switch ON, brake pedal depressed
|
7.5 to 14 V
|
Ignition switch ON, brake pedal released
|
0 to 1.5 V
|
ST1- (E6-14) - E1 (E7-7)
|
R-L - BR
|
Stop light switch (opposite to STP)
|
Ignition switch ON, brake pedal depressed
|
0 to 1.5 V
|
Ignition switch ON, brake pedal released
|
7.5 to 14 V
|
TC (E5-11) - E1 (E7-7)
|
P-B - BR
|
Terminal TC of DLC3
|
Ignition switch ON
|
11 to 14 V
|
W (E5-12) - E1 (E7-7)
|
R-B - BR
|
MIL
|
MIL illuminated
|
0 to 3 V
|
MIL not illuminated
|
11 to 14 V
|
SPD (E6-17) - E1 (E7-7)
|
V-R - BR
|
Speed signal from combination meter
|
Ignition switch ON, slowly rotate wheel
|
Pulse generation (see waveform 3)
|
PIM (E7-28) - E2 (E8-28)
|
L-B - BR
|
Manifold absolute pressure sensor
|
Apply negative pressure of 40 kPa (300 mmHg, 11.8 in.Hg)
|
0.1 to 0.7 V
|
Same as atmospheric pressure
|
0.8 to 1.5 V
|
Apply positive pressure of 170 kPa (1,275 mmHg, 50.2 in.Hg)
|
1.6 to 2.3 V
|
IREL (E5-10) - E1 (E7-7)
|
B-W - BR
|
EDU relay
|
Ignition switch ON
|
0 to 1.5 V
|
TACH (E5-4) - E1 (E7-7)
|
B-W - BR
|
Engine speed
|
Idling
|
Pulse generation (see waveform 4)
|
PCR1 (E8-26) - E2 (E8-28)
|
R-Y - BR
|
Common rail pressure sensor (main)
|
Idling
|
1.7 to 2.2 V
|
PCR2 (E8-33) - E2 (E8-28)
|
G-R - BR
|
Common rail pressure sensor (sub)
|
Idling
|
1.2 to 1.6 V
|
GREL (E5-15) - E1 (E7-7)
|
R - BR
|
GLOW relay
|
Cranking
|
11 to 14 V
|
THF (E8-29) - E2 (E8-28)
|
G-B - BR
|
Fuel temperature sensor
|
Ignition switch ON
|
0.5 to 3.4 V
|
ALT (E8-8) - E1 (E7-7)
|
G - BR
|
Generator duty ratio
|
Idling
|
Pulse generation (see waveform 5)
|
PCV+ (E8-2) - PCV- (E8-1)
|
G-W - G-Y
|
Suction control valve
|
Idling
|
Pulse generation (see waveform 6)
|
INJF (E8-25) - E1 (E7-7)
|
P - BR
|
EDU
|
Idling
|
Pulse generation (see waveform 7)
|
VNTO (E8-10)*5 - E1 (E7-7)
|
B-O - BR
|
Turbo motor driver
|
Idling
|
Pulse generation (see waveform 8)
|
VNTI (E8-17)*5 - E1 (E7-7)
|
R-B - BR
|
Turbo motor driver
|
Idling
|
Pulse generation (see waveform 9)
|
PRD (E8-32) - E1 (E7-7)
|
GR - BR
|
EDU
|
Ignition switch OFF
|
4 to 6.5 V
|
VLU (E7-29) - E2 (E8-28)
|
B - BR
|
Throttle position sensor
|
Ignition switch ON, throttle valve fully opened
|
3.6 to 4.2 V
|
Ignition switch ON, throttle valve fully closed
|
0.4 to 1.0 V
|
LUSL (E7-4) - E1 (E7-7)
|
GR - BR
|
Diesel throttle motor duty signal
|
Engine warmed up, racing engine
|
Pulse generation (see waveform 10)
|
SCV (E8-15)*5 - E01 (E8-7)
|
LG - W-B
|
VSV for No. 1 swirl control valve
|
Idling
|
0 to 1.5 V
|
Engine speed 2600 rpm or more
|
11 to 14 V
|
EGR (E7-9)*6 - E1 (E7-7)
|
L-R - BR
|
E-VRV (for E-EGR)
|
Ignition switch ON
|
Pulse generation (see waveform 11)
|
EGRC (E7-18)*5 - E1 (E7-7)
|
Y-B - BR
|
VSV (for EGR Cut)
|
Ignition switch ON, EGR cuts (accelerator pedal fully depressed)
|
0 to 1.5 V
|
EGLS (E7-33) - E1 (E7-7)
|
L-Y - BR
|
EGR valve position sensor
|
Ignition switch ON
|
0.6 to 1.4 V
|
Idling
|
1.9 to 2.9 V
|
CAN+ (E6-22)*1 - E1 (E7-7)
|
V - BR
|
CAN communication line
|
Ignition switch ON
|
Pulse generation (see waveform 12)
|
CAN- (E6-21)*1 - E1 (E7-7)
|
P - BR
|
CAN communication line
|
Ignition switch ON
|
Pulse generation (see waveform 13)
|