P0418 Secondary Air Injection System Control "A" Circuit
Diagnostic trouble codes · Vehicles built from Jun 2011
DESCRIPTION
- Refer to DTC P0412 (Click here).
| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0418 |
After cold engine starts, all of following conditions are met (1 trip detection logic): (a) Air Injection system does not operate (air pump OFF, ASV OFF) (b) Diagnostic signal from Air Injection Control Driver (AID) is 20% (c) Battery voltage is 8 V or more |
|
| P0418 |
After cold engine starts, all of following conditions are met (1 trip detection logic): (a) Air Injection system is operating (air pump ON, ASV ON) (b) Diagnostic signal from AID is 20% (c) Battery voltage is 8 V or more |
|
MONITOR DESCRIPTION
Air Injection Control Driver (AID) detects an open or short in the air pump and Air Switching Valve (ASV) circuit according to the terminal voltage and sends a signal as the diagnostic information to the ECM.When a cold engine is started, the ECM immediately transmits command signals to the AID to drive the air pump and ASV.
The AID outputs the ASV malfunction signal to the ECM if either: 1) the AID receives the command signal from the ECM to drive the ASV, but the AID output voltage to the ASV is low, or 2) the AID does not receive the command signal from the ECM to drive the ASV, but the AID output voltage to the ASV is high.
The ECM sets the DTC based on the diagnostic signal from the AID.
WIRING DIAGRAM
Refer to DTC P0412 (Click here).INSPECTION PROCEDURE
- HINT:
- The diagnostic information output from the AID can be confirmed by connecting an oscilloscope to the diagnostic information terminal of the AID.
-


- Connect the intelligent tester to the DLC3.
- Connect an oscilloscope probe to the AIDI terminal of the ECM.
- Start the engine and turn the tester ON.
- On the tester, select the following menu items: Powertrain / Engine and ECT / Data List.
- Monitor the output voltage of the AID (duty ratio signal).
- Oscilloscope range:
Item
Content
Tester Connection
AIDI - E1
Tool Setting
5 V/DIV., 20 to 40 msec./DIV.
Condition
Idling
| AID Diagnostic Signal Waveform |
ECM Command |
DTC (ECM Output) |
Suspected Trouble Area |
| 100% Duty Ratio See waveform 1 |
Any Air Injection (AI) System operation |
P1613 |
|
| 0% Duty Ratio See waveform 2 |
AI System: ON (Air pump ON, ASV ON) |
P1613 |
|
| AI System: OFF (Air pump OFF, ASV OFF) |
- |
|
|
| 20% Duty Ratio See waveform 3 |
Air Pump: ON |
P0418 |
|
| Air Pump: OFF |
P0418 |
|
|
| 40% Duty Ratio See waveform 4 |
ASV: ON |
P0412 |
|
| ASV: OFF |
P0412 |
|
|
| 80% Duty Ratio See waveform 5 |
AI System: OFF (Air pump OFF, ASV OFF) |
P1613 |
|
| AI System: ON (Air pump ON, ASV ON) |
- |
|
|
| Excluding Above (excluding 0, 20, 40, 80, 100% duty) |
- |
P1613 |
|
| Waveform 1 |
![]() ![]() |
- 100% Duty Ratio
| Waveform 2 |
![]() ![]() |
- 0% Duty Ratio
| Waveform 3 |
![]() ![]() |
- 20% Duty Ratio
| Waveform 4 |
![]() ![]() |
- 40% Duty Ratio
| Waveform 5 |
![]() ![]() |
- 80% Duty Ratio
- HINT:
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
| 1. INSPECT AIR PUMP ASSEMBLY |
![]() ![]() |
Disconnect the A21 air pump connector.
Measure the resistance of the air pump.
- Standard resistance:
Tester Connection
Specified Condition
1 - 2
0.2 to 10 Ω
|
|
||||
| OK | |
| 2. CHECK WIRE HARNESS (AIR PUMP - BODY GROUND) |
![]() ![]() |
Disconnect the A21 air pump connector.
Measure the resistance of the wire harness side connector.
- Standard resistance:
Tester Connection
Specified Condition
A21-1 - Body ground
Below 1 Ω
|
|
||||
| OK | |
| 3. CHECK WIRE HARNESS (AIR INJECTION DRIVER - AIR PUMP) |
![]() ![]() |
Disconnect the A21 air pump connector.
Disconnect the A19 AID connector.
Check the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
Specified Condition
A21-2 - A19-2
Below 1 Ω
|
|
||||
| OK | ||
| ||








