2014 Hilux · Service Manual TRANSMISSION

Park / Neutral Position Switch Circuit

Circuit diagnosis · Vehicles built Jun 2011 – Jul 2012

Versions by build date: Jun 2011 – Jul 2012 from Aug 2012

DESCRIPTION

The park/neutral position switch detects the shift lever position and sends signals to the ECM.

WIRING DIAGRAM

C169725E22

INSPECTION PROCEDURE


HINT:
Using the intelligent tester's Data List allows switch, sensor, actuator and other item values to be read without removing any parts. Reading the Data List early in troubleshooting is one way to save time.
  1. Warm up the engine.
  2. Turn the ignition switch OFF.
  3. Connect the intelligent tester to the DLC3.
  4. Turn the ignition switch ON and push the tester main switch ON.
  5. Enter the following menus: Powertrain / Engine and ECT / Data List.
  6. Follow the instructions on the tester and read the Data List.
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Neutral Position SW Signal
Park/neutral position switch status/
ON or OFF
Shift lever is:
  1. ON: On P or N
  2. OFF: Not on P or N
When shift lever position displayed on intelligent tester differs from actual position, adjustment of park/neutral position switch or shift cable may be incorrect
Shift SW Status (R Range)
Park/neutral position switch status/
ON or OFF
Shift lever is:
  1. ON: On R
  2. OFF: Not on R
When shift lever position displayed on intelligent tester differs from actual position, adjustment of park/neutral position switch or shift cable may be incorrect
Shift SW Status (D or 3 Range)
Park/neutral position switch status/
ON or OFF
Shift lever is:
  1. ON: On D or 3
  2. OFF: Not on D or 3
When shift lever position displayed on intelligent tester differs from actual position, adjustment of park/neutral position switch or shift cable may be incorrect
Shift SW Status (2 Range)
Park/neutral position switch status/
ON or OFF
Shift lever is:
  1. ON: On 2
  2. OFF: Not on 2
When shift lever position displayed on intelligent tester differs from actual position, adjustment of park/neutral position switch or shift cable may be incorrect
Shift SW Status (L Range)
Park/neutral position switch status/
ON or OFF
Shift lever is:
  1. ON: On L
  2. OFF: Not on L
When shift lever position displayed on intelligent tester differs from actual position, adjustment of park/neutral position switch or shift cable may be incorrect

CAUTION:
In the table above, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

HINT:
When the malfunction is found when the shift lever is on 3, start from *1. When the malfunction is found when the shift lever is not on 3, start from *2.


1. INSPECT PARK/NEUTRAL POSITION SWITCH*1

  1. C146745E18
    Disconnect the N1 park/neutral position switch connector.

  1. Measure the resistance of the park/neutral position switch when the shift lever is moved to each position.

    Standard resistance:
    Tester Connection
    Shift Lever Position
    Specified Condition
    4 (B) - 5 (L)
    P or N
    Below 1 Ω
    4 (B) - 5 (L)
    Not on P or N
    10 kΩ or higher
    1 (RL) - 2 (RB)
    R
    Below 1 Ω
    1 (RL) - 2 (RB)
    Not on R
    10 kΩ or higher
    2 (RB) - 7 (DL)
    D
    Below 1 Ω
    2 (RB) - 7 (DL)
    Not on D
    10 kΩ or higher
    2 (RB) - 3 (2L)
    2
    Below 1 Ω
    2 (RB) - 3 (2L)
    Not on 2
    10 kΩ or higher
    2 (RB) - 8 (LL)
    L
    Below 1 Ω
    2 (RB) - 8 (LL)
    Not on L
    10 kΩ or higher



NG
REPLACE PARK/NEUTRAL POSITION SWITCH
OK


2. INSPECT SHIFT LOCK CONTROL ECU*2

  1. C170575E02
    Disconnect the S43 ECU connector.

  1. Measure the resistance of the ECU when the shift lever is moved to each position.

    Standard resistance:
    Tester Connection
    Shift Lever Position
    Specified Condition
    9 (NSSD) - 3 (AT3)
    D
    10 kΩ or higher
    9 (NSSD) - 3 (AT3)
    3
    Below 1 Ω



NG
REPLACE SHIFT LOCK CONTROL ECU
OK


3. CHECK WIRE HARNESS (ECM - BATTERY)
C118533E15
  1. Turn the ignition switch ON.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Shift Lever Position
    Specified Condition
    E10-11 (R) - Body ground
    R
    10 to 14 V*
    E10-11 (R) - Body ground
    Not on R
    Below 1 V
    E10-19 (3) - Body ground
    D
    10 to 14 V
    E10-19 (3) - Body ground
    Not on D
    Below 1 V
    E10-10 (2) - Body ground
    2
    10 to 14 V
    E10-10 (2) - Body ground
    Not on 2
    Below 1 V
    E10-9 (L) - Body ground
    L
    10 to 14 V
    E10-9 (L) - Body ground
    Not on L
    Below 1 V

    HINT:
    *: The voltage will drop slightly due to the illumination of the back-up light.



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE ECM


← P2769/64 Short in Torque Converter Clutch Solenoid Circuit (Shift Solenoid Valve SL) (+ P2770/64) (from Aug 2014)Park / Neutral Position Switch Circuit (from Aug 2012) →