Park / Neutral Position Switch Circuit
Circuit diagnosis · Vehicles built Jun 2011 – Jul 2012
Versions by build date: Jun 2011 – Jul 2012 from Aug 2012
DESCRIPTION
The park/neutral position switch detects the shift lever position and sends signals to the ECM.WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- Using the intelligent tester's Data List allows switch, sensor, actuator and other item values to be read without removing any parts. Reading the Data List early in troubleshooting is one way to save time.
- Warm up the engine.
- Turn the ignition switch OFF.
- Connect the intelligent tester to the DLC3.
- Turn the ignition switch ON and push the tester main switch ON.
- Enter the following menus: Powertrain / Engine and ECT / Data List.
- Follow the instructions on the tester and read the Data List.
- Warm up the engine.
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Neutral Position SW Signal
Park/neutral position switch status/
ON or OFF
Shift lever is: - ON: On P or N
- OFF: Not on P or N
When shift lever position displayed on intelligent tester differs from actual position, adjustment of park/neutral position switch or shift cable may be incorrect
Shift SW Status (R Range)
Park/neutral position switch status/
ON or OFF
Shift lever is: - ON: On R
- OFF: Not on R
When shift lever position displayed on intelligent tester differs from actual position, adjustment of park/neutral position switch or shift cable may be incorrect
Shift SW Status (3 Range)
Park/neutral position switch status/
ON or OFF
Shift lever is: - ON: On 3
- OFF: Not on 3
When shift lever position displayed on intelligent tester differs from actual position, adjustment of park/neutral position switch or shift cable may be incorrect
Shift SW Status (2 Range)
Park/neutral position switch status/
ON or OFF
Shift lever is: - ON: On 2
- OFF: Not on 2
When shift lever position displayed on intelligent tester differs from actual position, adjustment of park/neutral position switch or shift cable may be incorrect
Shift SW Status (L Range)
Park/neutral position switch status/
ON or OFF
Shift lever is: - ON: On L
- OFF: Not on L
When shift lever position displayed on intelligent tester differs from actual position, adjustment of park/neutral position switch or shift cable may be incorrect
- ON: On P or N
- CAUTION:
- In the table above, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
- HINT:
- When the malfunction is found when the shift lever is on 3, start from *1. When the malfunction is found when the shift lever is not on 3, start from *2.
| 1. INSPECT PARK/NEUTRAL POSITION SWITCH*1 |
Disconnect the N1 park/neutral position switch connector.

Measure the resistance of the park/neutral position switch when the shift lever is moved to each position.
- Standard Resistance:
Tester Connection
Shift Lever Position
Specified Condition
4 (B) - 5 (L)
P or N
Below 1 Ω
4 (B) - 5 (L)
Not on P or N
10 kΩ or higher
1 (RL) - 2 (RB)
R
Below 1 Ω
1 (RL) - 2 (RB)
Not on R
10 kΩ or higher
2 (RB) - 7 (DL)
D
Below 1 Ω
2 (RB) - 7 (DL)
Not on D
10 kΩ or higher
2 (RB) - 3 (2L)
2
Below 1 Ω
2 (RB) - 3 (2L)
Not on 2
10 kΩ or higher
2 (RB) - 8 (LL)
L
Below 1 Ω
2 (RB) - 8 (LL)
Not on L
10 kΩ or higher
|
|
||||
| OK | |
| 2. INSPECT SHIFT LOCK CONTROL ECU*2 |
Disconnect the S43 ECU connector.

Measure the resistance of the ECU when the shift lever is moved to each position.
- Standard Resistance:
Tester Connection
Shift Lever Position
Specified Condition
9 (NSSD) - 3 (AT3)
D
10 kΩ or higher
9 (NSSD) - 3 (AT3)
3
Below 1 Ω
|
|
||||
| OK | |
| 3. CHECK WIRE HARNESS (ECM - BATTERY) |
![]() ![]() |
Turn the ignition switch ON.
Measure the voltage of the wire harness side connector.
- Standard Voltage:
Tester Connection
Shift Lever Position
Specified Condition
E10-11 (R) - Body ground
R
10 to 14 V*
E10-11 (R) - Body ground
Not on R
Below 1 V
E10-19 (3) - Body ground
D
10 to 14 V
E10-19 (3) - Body ground
Not on D
Below 1 V
E10-10 (2) - Body ground
2
10 to 14 V
E10-10 (2) - Body ground
Not on 2
Below 1 V
E10-9 (L) - Body ground
L
10 to 14 V
E10-9 (L) - Body ground
Not on L
Below 1 V
- HINT:
- *: The voltage will drop slightly due to the illumination of the back-up light.
|
|
||||
| OK | ||
| ||

