2014 Hilux · Service Manual TRANSMISSION

P2716/77 Pressure Control Solenoid "D" Electrical (Shift Solenoid Valve SLT)

Diagnostic trouble codes · Vehicles built from Jun 2011

DESCRIPTION

The throttle pressure that is applied to the primary regulator valve (which modulates the line pressure) causes the solenoid valve SLT, under electronic control, to precisely modulate and generate the line pressure according to the extent that the accelerator pedal is depressed or the output of engine power.
This controls the line pressure and provides smooth shifting characteristics.
Upon receiving a signal of the throttle valve opening angle, the ECM controls the line pressure by sending a predetermined duty ratio* to the solenoid valve, modulating the line pressure and generating throttle pressure.

HINT:
C170551E01
*: The duty ratio is the ratio of the current on time (A) to the total of the current on and off time (A + B).
Duty Ratio (%) = A / (A + B) x 100

DTC Code
DTC Detection Condition
Trouble Area
P2716/77
ECM detects shift solenoid valve SLT circuit malfunction for 1 sec. or more (1 trip detection logic)
  1. Open or short in shift solenoid valve SLT circuit
  2. Shift solenoid valve SLT
  3. ECM

WIRING DIAGRAM

C161203E20

INSPECTION PROCEDURE


1. INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SLT)

  1. C170576E02
    Disconnect the E1 wire connector.

  1. Measure the resistance of the transmission wire.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2 (SLT+) - 6 (SLT-)
    20°C (68°F)
    5.0 to 5.6 Ω
    2 (SLT+) - Body ground
    20°C (68°F)
    10 kΩ or higher
    6 (SLT-) - Body ground
    20°C (68°F)
    10 kΩ or higher



NG
Go to step 3
OK


2. CHECK WIRE HARNESS (SHIFT SOLENOID VALVE SLT - ECM)

  1. C192332E04
    Disconnect the E11 ECM connector.

  1. Measure the resistance of the wire harness side connector.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E11-12 (SLT+) - E11-13 (SLT-)
    20°C (68°F)
    5.0 to 5.6 Ω
    E11-12 (SLT+) - Body ground
    20°C (68°F)
    10 kΩ or higher
    E11-13 (SLT-) - Body ground
    20°C (68°F)
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE ECM

3. INSPECT SHIFT SOLENOID VALVE SLT
C162477E05
  1. Remove the shift solenoid valve SLT.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    5.0 to 5.6 Ω

  1. C170573E01
    Connect the battery's positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector. Then check that the valve moves and makes an operating noise.

    OK:
    Valve moves and makes an operating noise.


    HINT:
    C192331E04
    Reference: Inspect using an oscilloscope.
    Check the waveform of the ECM connector.

    OK:
    Refer to illustration
    Item
    Content
    Tester Connection
    E11-12 (SLT+) - E11-13 (SLT-)
    Tool Setting
    5 V/DIV., 1 msec./DIV.
    Condition
    Engine is idling



NG
REPLACE SHIFT SOLENOID VALVE SLT
OK

REPLACE TRANSMISSION WIRE


← P0973/62 Shift Solenoid "A" Control Circuit Low (Shift Solenoid Valve S1) (+ P0974/62, P0976/63, P0977/63) (from Jun 2011)P2769/64 Short in Torque Converter Clutch Solenoid Circuit (Shift Solenoid Valve SL) (+ P2770/64) (from Jun 2011) →