2014 Hilux · Service Manual TRANSMISSION

P0722 Output Speed Sensor Circuit No Signal

Diagnostic trouble codes · Vehicles built from Jun 2011

DESCRIPTION

The No. 2 vehicle speed sensor (SP2) detects the rotation speed of the transmission output shaft and sends signals to the TCM. The TCM determines the vehicle speed based on these signals.
AC voltage is generated in the No. 2 vehicle speed sensor (SP2) coil as the rotor mounted on the output shaft rotates, and this voltage is sent to the TCM.
The gear shift point and lock-up timing are controlled by the TCM based on the signals from the output speed sensor and throttle position sensor.
DTC No.
DTC Detection Condition
Trouble Area
P0722
  1. All conditions below are detected 500 times or more continuously (2 trip detection logic):
    1. No signal from No. 2 vehicle speed sensor (SP2) is input to TCM while 4 pulses of No. 1 vehicle speed sensor signal are sent
    2. Vehicle speed is 9 km/h (6 mph) or more for at least 4 sec.
    3. PNP switch is OFF
  1. Open or short in No. 2 vehicle speed sensor (SP2) circuit
  2. No. 2 vehicle speed sensor (SP2)
  3. TCM

MONITOR DESCRIPTION

The output speed sensor (SP2) monitors the output shaft speed. The TCM controls the gear shift point and the lock-up timing based on the signals from the output speed sensor (SP2) and throttle position sensor.
If the TCM detects no signal from the output speed sensor (SP2) even while the vehicle is moving, the TCM will conclude that the output shaft speed sensor (SP2) is malfunctioning. The TCM will illuminate the MIL and set the DTC.

WIRING DIAGRAM

A110970E06

INSPECTION PROCEDURE


1. CHECK SPEED SENSOR (INSTALLATION)

  1. BR03795E15
    Check the speed sensor installation.

    OK:
    Installation bolt is tightened properly and there is no clearance between sensor and transmission case.



NG
SECURELY INSTALL SPEED SENSOR OR REPLACE SPEED SENSOR
OK


2. INSPECT NO. 2 VEHICLE SPEED SENSOR
C058536E08
  1. Disconnect the T7 sensor connector from the transmission.

  1. Measure the resistance of the sensor.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    560 to 680 Ω


    HINT:
    G036609E01
    Reference: Inspect using an oscilloscope.
    Check the waveform of the TCM connector.

    OK:
    Refer to illustration.
    Item
    Content
    Tester Connection
    T19-30 (SP2+) - T19-29 (SP2-)
    Tool Setting
    2 V/DIV., 2 msec./DIV.
    Condition
    Vehicle speed 20 km/h (12 mph)



NG
REPLACE NO. 2 VEHICLE SPEED SENSOR
OK


3. CHECK WIRE HARNESS (NO. 2 VEHICLE SPEED SENSOR - TCM)

  1. F045523E03
    Disconnect the T19 TCM connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    T19-30 (SP2+) - T19-29 (SP2-)
    20°C (68°F)
    560 to 680 Ω
    T19-30 (SP2+) - Body ground
    20°C (68°F)
    10 kΩ or higher
    T19-29 (SP2-) - Body ground
    20°C (68°F)
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE TCM


← P0717 Input Speed Sensor Circuit No Signal (from Aug 2013)P0724 Brake Switch "B" Circuit High (from Jun 2011) →