2014 Hilux · Service Manual TRANSMISSION

P2769/64 Short in Torque Converter Clutch Solenoid Circuit (Shift Solenoid Valve SL)

Diagnostic trouble codes · Vehicles built Jun 2011 – Jul 2014

Also covers:

Versions by build date: Jun 2011 – Jul 2014 from Aug 2014

DESCRIPTION

The shift solenoid valve SL is turned ON and OFF by signals from the ECM to control the hydraulic pressure acting on the lock-up relay valve, which then controls the operation of the lock-up clutch.
DTC No.
DTC Detection Condition
Trouble Area
P2769/64
ECM detects short in shift solenoid valve SL circuit (once) when shift solenoid valve SL is operated (1 trip detection logic)
  1. Short in shift solenoid valve SL circuit
  2. Shift solenoid valve SL
  3. ECM
P2770/64
ECM detects open in shift solenoid valve SL circuit (once) when shift solenoid valve SL is not operated (1 trip detection logic)
  1. Open in shift solenoid valve SL circuit
  2. Shift solenoid valve SL
  3. ECM
Fail-safe function:
If the ECM detects a malfunction, it turns the shift solenoid valve SL OFF.

MONITOR DESCRIPTION

Torque converter lock-up is controlled by the ECM based on engine rpm, engine load, engine temperature, vehicle speed, transmission temperature, and shift position selection. The ECM determines the lock-up status of the torque converter by comparing the engine rpm (NE) to the input rpm (NC0). The ECM calculates the actual transmission gear by comparing the input rpm (NC0) to the output rpm (SP2). When conditions are appropriate, the ECM requests "lock-up" by applying control voltage to the shift solenoid valve SL. When the shift solenoid valve SL is opened, the shift solenoid valve SL applies pressure to the lock-up relay valve and locks the torque converter clutch. If the ECM detects an open or short in the shift solenoid valve SL circuit, the ECM interprets this as a fault in the shift solenoid valve SL or its circuit. The ECM will illuminate the MIL and store a DTC.

WIRING DIAGRAM

C161204E34

INSPECTION PROCEDURE


1. INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SL)

  1. C170576E07
    Disconnect the E1 wire connector.

  1. Measure the resistance of the transmission wire.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    7 (S3) - Body ground
    20°C (68°F)
    11 to 15 Ω



NG
Go to step 3
OK


2. CHECK WIRE HARNESS (SHIFT SOLENOID VALVE SL - ECM)

  1. C117621E33
    Disconnect the E11 ECM connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E11-11 (SL) - Body ground
    20°C (68°F)
    11 to 15 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE ECM

3. INSPECT SHIFT SOLENOID VALVE SL
C155226E05
  1. Remove the shift solenoid valve SL.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Shift solenoid valve SL connector terminal - Shift solenoid valve SL body
    20°C (68°F)
    11 to 15 Ω

  1. Connect the battery's positive (+) lead to the terminal of the solenoid valve connector, and the negative (-) lead to the solenoid valve body. Then check that the valve moves and makes an operating noise.

    OK:
    Valve moves and makes an operating noise.



NG
REPLACE SHIFT SOLENOID VALVE SL
OK

REPLACE TRANSMISSION WIRE


← P2716/77 Pressure Control Solenoid "D" Electrical (Shift Solenoid Valve SLT) (from Jun 2011)P2769/64 Short in Torque Converter Clutch Solenoid Circuit (Shift Solenoid Valve SL) (+ P2770/64) (from Aug 2014) →