2014 Hilux · Service Manual BODY ELECTRICAL

TERMINALS OF ECU

System information · Vehicles built from Aug 2013


CHECK NAVIGATION RECEIVER ASSEMBLY
E275623E02
  1. Disconnect the N12 and N9 navigation receiver assembly connectors.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specification
    N12-3 (ACC) - N12-7 (GND)
    GR - BR
    ACC signal
    Ignition switch off
    Below 1 V
    Ignition switch ACC
    11 to 14 V
    N12-4 (B) - N12-7 (GND)
    L-Y - BR
    Battery
    Always
    11 to 14 V
    N12-7 (GND) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω
    N9-1 (IG) - N12-7 (GND)
    P - BR
    IG signal
    Ignition switch off
    Below 1 V
    Ignition switch ON
    11 to 14 V
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the N12 and N9 navigation receiver assembly connectors.

  4. Measure the voltage and waveform according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specification
    N9-2 (REV) - N12-7 (GND)
    R-Y - BR
    Reverse signal
    Ignition switch ON, shift lever in R
    7.5 to 14 V
    Ignition switch ON, shift lever not in R
    Below 1 V
    N10-11 (CA+) - N10-23 (CGND)
    B - Shielded
    Power source
    Ignition switch ACC
    5.5 to 7.05 V
    N10-12 (V+) - N10-24 (V-)
    W - R
    Display signal
    Ignition switch ON, shift lever in R
    Pulse generation (See waveform 1)
    Ignition switch ON, shift lever in R, screen blacked out by covering camera lens
    Pulse generation (See waveform 2)
    N10-23 (CGND) - Body ground
    Shielded - Body ground
    Shielding
    Always
    Below 1 V
    If the result is not as specified, the navigation receiver assembly may have a malfunction.

  5. E171712E24
    Using an oscilloscope, check the waveform.

    1. Waveform 1

      Measurement Condition 
      Item
      Content
      Terminal No. (Symbol)
      N10-12 (V+) - N10-24 (V-)
      Tool Setting
      0.2 V/DIV., 50 μs/DIV.
      Condition
      Ignition switch ON, shift lever in R

      HINT:
      The video waveform changes according to the image sent by the rear television camera assembly.

    2. Waveform 2

      Measurement Condition 
      Item
      Content
      Terminal No. (Symbol)
      N10-12 (V+) - N10-24 (V-)
      Tool Setting
      0.2 V/DIV., 50 μs/DIV.
      Condition
      Ignition switch ON, shift lever in R, screen blacked out by covering camera lens

      HINT:
      The video waveform changes according to the image sent by the rear television camera assembly.

      Text in Illustration 
      *a
      Waveform 1
      *b
      Waveform 2
      *c
      Synchronized Signal
      *d
      Video Waveform

← PROBLEM SYMPTOMS TABLE (from Aug 2013)DTC CHECK / CLEAR (from Aug 2013) →