2014 Hilux · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built from Aug 2013

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013


1. INSTALL THERMOSTAT

  1. A110388E01
    Install a new gasket to the thermostat.

    HINT:
    When installing the thermostat to the gasket, be careful not to deform the gasket. Make sure that the thermostat is properly installed into the groove of the gasket, as shown in the illustration.

  1. Insert the thermostat into the cylinder block with the jiggle valve facing straight upward.

    HINT:
    The jiggle valve may be set within 30°of either side of the prescribed position.


2. INSTALL WATER INLET

  1. A097637E01
    Install the water inlet with the 3 bolts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }


3. CONNECT RADIATOR HOSE OUTLET
  1. Connect the radiator hose outlet to the water inlet.


4. CONNECT NO. 1 AUTOMATIC TRANSMISSION OIL COOLER TUBE CLAMP (for Automatic Transmission)
  1. Connect the No. 1 automatic transmission oil cooler tube clamp to the water inlet with the bolt.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }


5. INSTALL COMPRESSOR INLET ELBOW (w/ Intercooler)
  1. for Type B:
    Connect the 2 No. 1 turbo water hoses to the No. 2 water by-pass pipe sub-assembly and the cylinder block sub-assembly, and slide the 4 clamps to secure the hoses.

  1. for Type A:

    1. Install the No. 12 water by-pass hose to the compressor inlet elbow, and slide the 2 clamps to secure the hose.

    2. Install the No. 7 water by-pass hose to the compressor inlet elbow, slide the clamp to secure the hose.

  1. Install a new gasket and the compressor inlet elbow with the 2 nuts.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }

  1. for Type A:

    1. Connect the No. 13 water by-pass hose to the No. 2 water by-pass pipe sub-assembly, and slide the clamp to secure the hose.

    2. Connect the No. 2 water by-pass hose to the compressor inlet elbow, and slide the clamp to secure the hose.

    3. Connect the No. 1 turbo water hose to the cylinder block sub-assembly, and slide the clamp to secure the hose.

  1. Connect the 2 connectors and attach the wire harness clamp.


6. INSTALL VENTILATION PIPE (w/ Intercooler)
  1. Install the ventilation pipe with the bolt.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. for Type A:
    Connect the No. 12 water by-pass hose and No. 13 water by-pass hose to the ventilation pipe, and slide the 2 clamps to secure the hoses.


7. INSTALL AIR CLEANER ASSEMBLY
  1. w/o Mass Air Flow Meter:

    1. Connect the air cleaner hose.

    2. Install the air cleaner assembly with the 2 bolts.

      Torque:
      14 N*m{ 143 kgf*cm , 10 ft.*lbf }

    3. Tighten the clamp.

    4. Attach the clamp and connect the intake air temperature sensor connector.

    5. Connect the ventilation hose to the cylinder head cover sub-assembly, and slide the clamp to secure the hose.

  1. w/ Mass Air Flow Meter:

    1. Connect the No. 1 air cleaner hose.

    2. Install the air cleaner assembly with the 2 bolts.

      Torque:
      14 N*m{ 143 kgf*cm , 10 ft.*lbf }

    3. w/o Intercooler:
      Connect the ventilation hose to the cylinder head cover sub-assembly, and slide the clamp to secure the hose.

    4. Connect the connector to the mass air flow meter.

    5. Tighten the hose clamp.


8. INSTALL VENTILATION HOSE HEAT INSULATOR (w/o Intercooler)
  1. Install the ventilation hose heat insulator with the 2 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }


9. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

10. INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY (w/ No. 1 Engine Cover)
  1. Connect the pipe (with the 2 air hoses) and install the bolt.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Tighten the 2 clamps.

  1. Connect the vacuum hose to the gas filter.

  1. Connect the manifold absolute pressure sensor connector.

  1. w/ No. 1 Engine Cover

    1. Install the engine cover bracket with the 2 bolts.

      Torque:
      18 N*m{ 184 kgf*cm , 13 ft.*lbf }

    2. Attach the 4 claws to the pins of the engine cover bracket and install the No. 1 engine cover sub-assembly.


11. ADD ENGINE COOLANT
  1. Tighten the radiator drain cock plug by hand.

  1. Tighten the cylinder block drain cock plug.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. A098989E01
    Fill the radiator with TOYOTA Super Long Life Coolant (SLLC) to the reservoir tank's B line.

    Standard Capacity:
    Item
    Specified Condition
    for Automatic Transmission
    11.1 liters (11.7 US qts, 9.8 Imp. qts)
    for Manual Transmission
    9.8 liters (10.4 US qts, 8.6 Imp. qts)

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
    1. Please contact your TOYOTA dealer for further details.

    NOTICE:
    Never use water as a substitute for engine coolant.

  1. Press the radiator hose inlet and radiator hose outlet several times by hand, and then check the level of the coolant.
    If the coolant level drops below the B line, add TOYOTA SLLC to the B line.

  1. Install the radiator reservoir cap.

  1. A099591E01
    Using a wrench, install the vent plug.

    Torque:
    2.0 N*m{ 20 kgf*cm , 18 in.*lbf }

  1. Bleed air from the cooling system.

    1. Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.

    2. Maintain the engine speed at 2500 to 3000 rpm.

    3. Press the radiator hose inlet and radiator hose outlet several times by hand to bleed air.

      CAUTION:
      When pressing the radiator hoses:
      1. Wear protective gloves.
      1. Be careful as the radiator hoses are hot.
      1. Keep your hands away from the radiator fan.

    4. Stop the engine and wait until the coolant cools down to ambient temperature.

      CAUTION:
      Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. G036768E01
    After the coolant cools down, check that the coolant level is at the F line.
    If the coolant level is below the F line, add TOYOTA SLLC to the F line.


12. INSPECT FOR COOLANT LEAK

NOTICE:
Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. A097645E01
    Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2 ,17.1 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leaks.
    If no external leaks are found, check the cylinder block and head.


13. INSTALL INTERCOOLER ASSEMBLY (w/ Intercooler)
(Click here)

14. INSTALL NO. 1 ENGINE UNDER COVER (for 4WD and Pre-Runner)

Torque:
28 N*m{ 286 kgf*cm , 21 ft.*lbf }


15. PERFORM INITIALIZATION
  1. Perform initialization (Click here).

    NOTICE:
    Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.

← INSTALLATION (Aug 2012 – Jul 2013)COMPONENTS (from Jun 2011) →