2014 Hilux · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Aug 2012

Versions by build date: Jun 2011 – Jul 2012 from Aug 2012


1. REMOVE INTERCOOLER ASSEMBLY
(Click here)

2. REMOVE NO. 1 ENGINE UNDER COVER

3. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the radiator drain cock plug.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. A099591E01
    Drain the coolant by removing the reservoir cap and, using a wrench, remove the vent plug.

  1. Loosen the cylinder block drain cock plug.

    A147246E01


4. REMOVE AIR CLEANER ASSEMBLY

  1. A271954
    Detach the wire harness clamp and disconnect the mass air flow meter connector.

  1. Loosen the hose clamp and disconnect No. 1 air cleaner hose from the compressor inlet elbow.

  1. Remove the 2 bolts and air cleaner assembly together with the No. 1 air cleaner hose.


5. REMOVE VENTILATION PIPE

  1. A288742
    for Cold Area Specification Vehicles:
    Disconnect the No.12 water by-pass hose and No. 13 water by-pass hose.

  1. A288747E01
    Remove the bolt and ventilation pipe.
    Text in Illustration 
    *A
    except Cold Area Specification Vehicles
    *B
    for Cold Area Specification Vehicles


6. REMOVE COMPRESSOR INLET ELBOW

  1. A288737
    Disconnect the 2 connectors and detach the wire harness clamp.

  1. A288738
    Disconnect the No. 1 turbo water hose.

  1. Disconnect the No. 2 water by-pass hose.

    A289859E01

    Text in Illustration 
    *A
    except Cold Area Specification Vehicles
    *B
    for Cold Area Specification Vehicles
    *1
    No. 2 Water By-pass Hose
    *2
    No. 9 Water By-pass Hose
    *3
    No. 13 Water By-pass Hose
    -
    -

  1. except Cold Area Specification Vehicles:
    Disconnect the No. 9 water by-pass hose.

  1. for Cold Area Specification Vehicles:
    Remove the No. 13 water by-pass hose.

  1. Remove the 2 nuts, compressor inlet elbow and gasket.

  1. A289860E01
    Remove the No. 7 water by-pass hose.
    Text in Illustration 
    *A
    except Cold Area Specification Vehicles
    *B
    for Cold Area Specification Vehicles
    *1
    No. 7 Water By-pass Hose
    *2
    No. 9 Water By-pass Hose
    *3
    No. 12 Water By-pass Hose

  1. except Cold Area Specification Vehicles:
    Remove the No. 9 water by-pass hose.

  1. for Cold Area Specification Vehicles:
    Remove the No. 12 water by-pass hose.


7. DISCONNECT NO. 1 AUTOMATIC TRANSMISSION OIL COOLER TUBE CLAMP (for Automatic Transmission)

A097634E01
  1. Remove the bolt and disconnect the No. 1 automatic transmission oil cooler tube clamp.


8. DISCONNECT RADIATOR HOSE OUTLET
  1. Disconnect the radiator hose outlet from the water inlet.


9. REMOVE WATER INLET

A250419
  1. Disconnect the wire harness clamp.

  1. Remove the 3 bolts and water inlet.

  1. Remove the bolt and wire harness clamp bracket from the water inlet.


10. REMOVE THERMOSTAT
  1. Remove the thermostat from the cylinder block.

  1. Remove the gasket from the thermostat.

← REMOVAL (Jun 2011 – Jul 2012)INSPECTION (from Jun 2011) →