2014 Hilux · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Aug 2012

Versions by build date: Jun 2011 – Jul 2012 from Aug 2012


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.


2. REMOVE NO. 1 ENGINE UNDER COVER (for 4WD)

3. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the radiator drain cock plug.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. A099591E01
    Drain the coolant by removing the reservoir cap and, using a wrench, remove the vent plug.

  1. Loosen the cylinder block drain cock plug.

    A147246E01


4. REMOVE AIR CLEANER ASSEMBLY
  1. w/o EGR Cooler:
    Disconnect the ventilation hose.

  1. w/ Mass Air Flow Meter:
    Disconnect the mass air flow meter sensor connector.

  1. w/ Intake Air Temperature Sensor:
    Disconnect the intake air temperature sensor connector.

  1. Loosen the hose clamp.

  1. Remove the 2 bolts and air cleaner.


5. REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

  1. A135916
    Remove the 3 bolts, 2 nut and engine cover.


6. REMOVE INTERCOOLER ASSEMBLY

  1. A149802
    Detach the 2 clamps.

  1. Disconnect the vacuum hose from the manifold absolute pressure sensor.

  1. Disconnect the IAT sensor connector and manifold absolute diesel pressure sensor connector.

  1. A149933
    Loosen the 2 hose clamps of the No. 1 air hose.

  1. A149934
    Loosen the 2 hose clamps of the No. 2 air hose.

  1. A135919
    Remove the 4 bolts and intercooler.


7. REMOVE VENTILATION PIPE

  1. A289877
    for Waste Gate Type Turbocharger:
    Remove the bolt and ventilation pipe.

  1. for Variable Nozzle Vane Turbocharger:

    1. A288742
      Disconnect the No. 12 water by-pass hose and No. 13 water by-pass hose.

    2. A288745
      Remove the bolt and ventilation pipe.


8. REMOVE COMPRESSOR INLET ELBOW (for Waste Gate Type Turbocharger)

  1. A289876
    Loosen the clamp, and then remove the compressor inlet elbow and air cleaner hose assembly from the turbocharger sub-assembly.

  1. Loosen the clamp, remove the air cleaner hose assembly from the compressor inlet elbow.

  1. Remove the No. 3 air cleaner hose from the turbo charger sub-assembly.


9. REMOVE COMPRESSOR INLET ELBOW (for Variable Nozzle Vane Turbocharger)

  1. A288737
    Disconnect the 2 connectors and detach the wire harness clamp.

  1. A291249
    Disconnect the No. 1 turbo water hose.

  1. A288735E01
    Disconnect the No. 2 water by-pass hose.
    Text in Illustration 
    *1
    No. 2 Water By-pass Hose
    *2
    No. 13 Water By-pass Hose

  1. Remove the No. 12 water by-pass hose and No. 13 water by-pass hose.

  1. Remove the 2 nuts, compressor inlet elbow and gasket.

  1. A288733E01
    Remove the No. 7 water by-pass hose and No. 12 water by-pass hose.
    Text in Illustration 
    *1
    No. 7 Water By-pass Hose
    *2
    No. 12 Water By-pass Hose


10. DISCONNECT RADIATOR HOSE OUTLET
  1. Disconnect the radiator hose outlet from the water inlet.


11. REMOVE WATER INLET

A097637E01
  1. Remove the 3 bolts and water inlet.


12. REMOVE THERMOSTAT
  1. Remove the thermostat from the cylinder block.

  1. Remove the gasket from the thermostat.

← REMOVAL (Jun 2011 – Jul 2012)INSPECTION (from Jun 2011) →