2014 Hilux · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Jun 2011


1. REMOVE ENGINE ASSEMBLY
  1. Remove the engine assembly (Click here).


2. REMOVE TIMING BELT
  1. Remove the timing belt (Click here).


3. REMOVE INJECTION PIPE SUB-ASSEMBLY

  1. A121940
    Using a union nut wrench, loosen the 8 union nuts of the 4 injection pipes.

  1. Remove the 2 nuts, 2 upper pipe clamps and 4 injection pipes with lower pipe clamps.


4. REMOVE INJECTION PUMP DRIVE PULLEY

  1. A071313E01
    Using SST, remove the pulley nut.
    SST
    09213-14010   (91651-60865)
    09330-00021  

  1. A071314E01
    Using SST, remove the drive pulley.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05010, 09954-05021)


5. REMOVE INJECTION PUMP ASSEMBLY

  1. A121086E01
    Disconnect the engine speed sensor connector.

  1. Disconnect the spill control valve connector.

  1. Disconnect the correction unit connector.

  1. Disconnect the timing control valve connector.

  1. Disconnect the fuel temperature sensor connector.

  1. Disconnect the engine wire clamp.

  1. Disconnect the 3 fuel hoses.

  1. A071318E01
    Remove the 3 bolts and injection pump stay.

  1. Remove the 2 nuts and injection pump.


6. REMOVE CAMSHAFT TIMING PULLEY

  1. Set the No. 1 cylinder to approx. 90° BTDC/compression.

    HINT:
    Set the No. 1 cylinder to 90° BTDC/compression to avoid interference with the piston top and valve head.


    1. A057443E03
      Using the crankshaft pulley bolt, turn the crankshaft 90°counterclockwise, and put the timing mark of the crankshaft timing pulley with the protrusion of the timing belt case.

  1. A056901E02
    Using SST, loosen the pulley bolt.
    SST
    09960-10010   (09962-01000, 09963-01000)

  1. A056903E02
    Using SST, disconnect the timing pulley from the camshaft.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05010, 09954-05021)

  1. Remove the pulley bolt and timing pulley.

  1. Remove the timing pulley woodruff key.


7. REMOVE NO. 2 TIMING BELT COVER
  1. Remove the 4 bolts and timing belt cover.


8. REMOVE WATER PUMP ASSEMBLY

  1. A031001E01
    Remove the 6 bolts and tension spring bracket.

  1. Remove the water pump and gasket.


9. REMOVE NO. 1 TIMING BELT IDLER SUB-ASSEMBLY

  1. A056838E06
    Remove the 2 bolts (A and B).

  1. Loosen the bolt (C), and remove the No. 1 timing belt idler.


10. REMOVE NO. 2 TIMING BELT IDLER SUB-ASSEMBLY
  1. Remove the bolt, No. 2 timing belt idler and spacer.


11. REMOVE CRANKSHAFT TIMING PULLEY

  1. A056898E03
    Using SST, remove the timing pulley.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05010, 09953-05020, 09954-05010)


12. REMOVE OIL PAN SUB-ASSEMBLY
  1. Remove the 16 bolts and 2 nuts.

  1. A057637E02
    Insert the blade of SST between the oil pan and cylinder block, cut off the applied sealer and remove the oil pan.
    SST
    09032-00100  

    NOTICE:
    1. Do not use SST for the timing belt case side and rear oil seal retainer.
    2. Be careful not to damage the oil pan flange.


13. REMOVE OIL STRAINER SUB-ASSEMBLY
  1. Remove the 2 bolts, 2 nuts, oil strainer and gasket.


14. REMOVE TIMING BELT CASE SUB-ASSEMBLY

  1. A056912E01
    Remove the 5 bolts, timing belt case and gasket.

← COMPONENTS (from Jun 2011)DISASSEMBLY (from Jun 2011) →