2014 Hilux · Service Manual ENGINE

ON-VEHICLE INSPECTION

Inspection · Vehicles built Jun 2011 – Jul 2012

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013


CHECK ENGINE IDLE SPEED AND MAXIMUM SPEED

HINT:
  1. For more information about the intelligent tester, refer to its operator's manual.
  2. If an intelligent tester is not available, use a tachometer's tester probe as a substitute.

  1. C108852E01
    Connect the intelligent tester to the DLC3.

  1. A082779E58
    If a tester is not available, connect a tester probe of a tachometer to terminal 9 (TAC) of the DLC3 with SST.
    SST
    09843-18040  

  1. Inspect the idle speed.

    HINT:
    1. The engine is warmed up.
    2. The A/C switch is OFF.


    1. Start the engine and measure the idle speed.

      Standard idle speed:
      700 to 800 rpm

      If the idle speed is not as specified, perform the troubleshooting procedures in the Diagnostics section.

  1. Inspect the maximum speed.

    1. Start the engine.

    2. Fully depress the accelerator pedal.

    3. Measure the maximum speed.

      Standard maximum speed:
      4450 to 4750 rpm

      If the maximum speed is not as specified, perform the troubleshooting in the Diagnostics section.

  1. If the tester probe of the tachometer is connected to the DLC3, disconnect the tester probe with SST from terminal 9 of the DLC3.

  1. Disconnect the intelligent tester from the DLC3.


INSPECT CYLINDER COMPRESSION PRESSURE

HINT:
Measure the compression pressure if the engine power is insufficient, oil is consumed excessively and/or fuel economy is poor.

  1. Remove the 4 glow plugs.

  1. Disconnect the 4 injector connectors.

  1. Turn the ignition switch to START to expel soot and other foreign matter from the inside of the cylinder.

  1. A038771E02
    Measure the compression pressure.

    1. Set SST (attachment) into the glow plug hole.

      SST
      09992-00025   (09992-00121)

      Torque:
      13 N*m{ 133 kgf*cm , 10 ft.*lbf }

    2. Connect SST (compression gauge) to SST (attachment).

      SST
      09992-00025   (09992-00211)

    3. Measure the compression pressure while cranking the engine.

      HINT:
      Always use a fully charged battery to obtain an engine revolution of 250 rpm or more.

  1. Perform the step above for each cylinder.

    NOTICE:
    This measurement must be done in as short a time as possible.

    Standard compression pressure:
    2700 kPa (27.5 kgf/cm2, 391 psi) or more

    Minimum pressure:
    2200 kPa (22.5 kgf/cm2, 320 psi)

    Standard difference between each cylinder:
    500 kPa (5.0 kgf/cm2, 71 psi) or less

    If the compression in one or more cylinders is low, add a bit of engine oil into the glow plug hole. Then, repeat the step above for the low-compression cylinder(s).

    HINT:
    1. If poor compression improves after adding the engine oil, the piston rings and/or cylinder bore may be worn or damaged.
    2. If pressure stays low, a valve may be stuck or seated improperly, or pressure may be leaking through the gasket.

  1. Remove SST (attachment and compression gauge).

  1. Connect the 4 injector connectors.

  1. Install the 4 glow plugs.

← REPAIR (from Jun 2011)ON-VEHICLE INSPECTION (Aug 2012 – Jul 2013) →