2014 Hilux · Service Manual ENGINE

DISASSEMBLY

Removal / installation · Vehicles built from Jun 2011

NOTICE:
  1. When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.
  2. When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.


1. REMOVE OIL FILLER CAP SUB-ASSEMBLY

2. REMOVE NOZZLE HOLDER SEAL
  1. Remove the 4 nozzle holder seals.


3. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

NOTICE:
If the cylinder head cover is removed, replace the 4 No. 3 cylinder head cover gaskets with new ones.

  1. G034844E02
    Disconnect the ventilation hose.

  1. Disconnect the 4 injector connectors.

  1. A060180E01
    Using a small screwdriver, remove the 4 nozzle holder seals by prying the portion between each nozzle holder seal and the cutout part of the cylinder head cover.

  1. G034877E01
    Remove the 10 bolts, 2 nuts, cylinder head cover and gasket.

  1. A289511
    Remove the 4 No. 3 cylinder head cover gaskets from the cylinder head cover.


4. REMOVE CAMSHAFT TIMING PULLEY

A060182E01
  1. Remove the bolt of the camshaft timing pulley by holding the camshaft with a wrench.

    NOTICE:
    Make sure to remove the bolt of the camshaft timing pulley with the timing belt not installed.

  1. Remove the camshaft timing pulley.


5. REMOVE NO. 2 TIMING BELT COVER
  1. Remove the 4 bolts, nut and timing belt cover.


6. REMOVE CYLINDER BLOCK INSULATOR (w/ EGR Cooler)

  1. A149941
    Remove the cylinder block insulator form the head.


7. REMOVE INJECTOR ASSEMBLY

  1. A061112E01
    Remove the union bolt, 4 hollow screws, 5 gaskets and nozzle leakage pipe.

    NOTICE:
    1. When removing the nozzle leakage pipe, place a cushion under the pipe.
    2. Be careful not to deform or scratch the union seal surface.
    3. After removing the fuel pipe, put it in a plastic bag to prevent foreign matter from contaminating its injector inlet.

  1. G034876E01
    Remove the 4 bolts, 4 washers, 4 nozzle holder clamps and 4 injectors.

    HINT:
    Arrange the injectors, nozzle holder clamps, washers and bolts in the correct order.

  1. Remove the O-ring from each injector.

  1. Remove the 4 injection nozzle seats from the cylinder head.


8. REMOVE CAMSHAFT

  1. A060148E02
    Face the key groove of the camshaft upward by turning the camshaft with a wrench.

  1. A060147E01
    Uniformly loosen the 15 bearing cap bolts in several passes in the sequence shown in the illustration.

  1. Remove the 5 bearing caps, oil seal and 2 camshafts.


9. REMOVE CYLINDER HEAD SUB-ASSEMBLY

A059194E01
  1. Uniformly loosen and remove the 18 cylinder head bolts in several passes in the sequence shown in the illustration.

    NOTICE:
    Head warpage or cracking could result from removing bolts in the incorrect order.

  1. Lift the cylinder head from the dowels on the cylinder block, and place the cylinder head on wooden blocks on a bench.

    HINT:
    If the cylinder head is difficult to lift, use a screwdriver to pry between the cylinder head and block.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head and cylinder block.


10. REMOVE WATER PUMP ASSEMBLY

A225339
  1. Remove the 5 bolts, 2 nuts, water pump and gasket.


11. REMOVE TIMING GEAR COVER

  1. A051308E01
    Remove the 14 bolts and 2 nuts.

  1. A051309E01
    Pry the gear cover at the locations shown in the illustration, and remove the gear cover together with the injection gear.

    NOTICE:
    Be careful not to drop the injection gear.

  1. A222328
    Remove the O-ring from the timing gear case.


12. REMOVE INJECTION GEAR

  1. A222329
    Secure the No. 2 idle sub gear to the No. 1 idle gear with a service bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    NOTICE:
    If the bolt hole of the No. 2 idle sub gear is not aligned with the bolt hole of the No. 1 idle gear, rotate the crankshaft counterclockwise to align the bolt holes. Then install the service bolt.

  1. A222330
    Remove the injection gear.


13. REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE

  1. A222331
    Remove the No. 1 camshaft position sensor plate.


14. REMOVE CRANKSHAFT TIMING GEAR

  1. A222332E01
    Using SST, remove the crankshaft timing gear.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05010, 09954-05021)


15. REMOVE IDLE GEAR THRUST PLATE

  1. A222333
    Remove the 2 bolts and thrust plate.


16. REMOVE NO. 1 IDLE GEAR

  1. A222337
    Remove the No. 1 idle gear together with the No. 2 idle sub gear.


17. REMOVE NO. 2 IDLE SUB GEAR

  1. A060164E02
    Using SST, turn the No. 2 idle sub gear clockwise and remove the service bolt.
    SST
    09960-10010   (09962-01000, 09963-00700)

  1. A060168E01
    Using snap ring pliers, remove the snap ring.

  1. Remove the wave washer, No. 2 idle sub gear and gear spring.


18. REMOVE NO. 1 IDLE GEAR SHAFT

  1. A222335
    Remove the idle gear shaft.


19. REMOVE ENGINE OIL LEVEL SENSOR
  1. Remove the 4 bolts and engine oil level sensor.


20. REMOVE OIL PAN SUB-ASSEMBLY

A057637E04
  1. Remove the 4 bolts and oil level gauge sensor.

  1. Remove the 22 bolts and 2 nuts.

  1. Insert the blade of a oil pan seal cutter between the oil pan and cylinder block, cut through the applied sealer and remove the oil pan.

    NOTICE:
    1. Do not use a oil pan seal cutter for the timing belt case side and rear oil seal retainer.
    2. Be careful not to damage the oil pan flange.


21. REMOVE OIL STRAINER SUB-ASSEMBLY
  1. Remove the 2 bolts, 2 nuts, oil strainer and gasket.


22. REMOVE TIMING GEAR CASE ASSEMBLY

A060153E01
  1. Remove the union bolt and 8 bolts.

  1. Pry the gear case in the location shown in the illustration, and remove the gear case, driven rotor and gasket.

  1. Remove the 2 O-rings.


23. REMOVE ENGINE REAR OIL SEAL RETAINER

  1. A052295E01
    Remove the 5 bolts.

  1. Using a screwdriver, remove the oil seal retainer by prying the portions between the oil seal retainer and cylinder block.


24. REMOVE CYLINDER BLOCK OIL ORIFICE

25. REMOVE PISTON AND CONNECTING ROD

A060199E03
  1. Check the matchmarks on the connecting rod and cap to ensure correct reassembly.

  1. Remove the 2 connecting rod cap bolts.

  1. A060236E01
    Using the 2 removed connecting rod bolts, pry the connecting rod cap back and forth, and remove the connecting cap.

    HINT:
    Keep the lower bearing inserted with the connecting rod cap.

  1. Clean the crank pin and bearing.

  1. Check the crank pin and bearing for pitting and scratches.
    If the crank pin or bearing is damaged, replace the bearings. If necessary, grind or replace the crankshaft.

  1. A060191E01
    Using a ridge reamer, remove all the carbon from the top of the cylinder.

  1. Push the piston, connecting rod assembly and upper bearing through the top of the cylinder block.

    HINT:
    1. Keep the bearings, connecting rod and cap together.
    2. Be sure to organize the removed piston and connecting rod assemblies in such a way that they can be reinstalled exactly as before.


26. REMOVE PISTON PIN

  1. A060231E02
    Check the fit between the piston pin and connecting rod.

    1. Check that the piston moves smoothly.
      If the piston does not move smoothly, replace the piston pin and connecting rod.

  1. A149752
    Using a piston ring expander, remove the 2 compression rings.

    HINT:
    Be sure to organize the removed piston rings in such a way that they can be reinstalled exactly as before.

  1. Remove the coil and oil ring by hand.

  1. Disconnect the connecting rod from the piston.

    1. A149754
      Using a small screwdriver, pry off the 2 snap rings from the piston.

    2. A060213E02
      Gradually heat the piston to approximately. 80°C (176°F).

    3. A060212E01
      Using a plastic-faced hammer and brass bar, lightly tap out the piston pin and pin. Then remove the connecting rod.

      HINT:
      1. The piston and pin are a matched set.
      2. Be sure to organize the removed pistons, pins, rings, connecting rods and bearings in such a way that the parts can be reinstalled exactly as before.


27. REMOVE CRANKSHAFT SUB-ASSEMBLY

  1. A060270E09
    Uniformly loosen and remove the 10 crankshaft bearing cap bolts in several passes, in the sequence shown.

  1. A060227E01
    Using the removed crankshaft bearing cap bolts, pry the cap back and forth, and remove the crankshaft bearing caps, lower crankshaft bearings and lower thrust washers (No. 3 crankshaft bearing cap only).

    HINT:
    1. Keep the lower crankshaft bearing and crankshaft bearing cap together.
    2. Be sure to organize the bearing caps and lower thrust washers in such a way that they can be reinstalled exactly as before.

  1. Lift out the crankshaft.

  1. Remove the upper bearings and upper thrust washers from the cylinder block.

    HINT:
    Arrange the main bearing caps, bearings and thrust washers in the correct order.


28. REMOVE NO. 1 OIL NOZZLE SUB-ASSEMBLY
  1. Remove the 4 check valves and oil nozzles.


29. REMOVE NO. 1 HEAD STRAIGHT SCREW PLUG
  1. Remove the screw plug and gasket.

← COMPONENTS (from Jun 2011)INSPECTION (Jun 2011 – Jul 2012) →