2014 Hilux · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built Jun 2011 – Jul 2012

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013


1. INSTALL INJECTOR ASSEMBLY

A075654E05
  1. Install a new insulator to each fuel injector.

  1. Apply a light coat of spindle oil or gasoline to a new O-ring and install it to each fuel injector.

  1. A075655E03
    While turning the fuel injector left and right, install it to the fuel delivery pipe.

  1. Position the fuel injector connector outward.


2. INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY

A075656E02
  1. Place the fuel delivery pipe together with the 6 fuel injectors on the intake manifold.

  1. Temporarily install the 6 bolts which are used to hold the fuel delivery pipe to the intake manifold.

  1. Check that the fuel injectors rotate smoothly.

    HINT:
    If the fuel injectors do not rotate smoothly, the probable cause is incorrect installation of O-ring. Replace the O-ring.

  1. Position the fuel injector connector outward.

  1. Tighten the 6 bolts which are used to hold the fuel delivery pipe to the intake manifold.

    Torque:
    15 N*m{ 153 kgf*cm , 11 ft.*lbf }

  1. Connect the 6 fuel injector connectors.


3. CONNECT NO. 2 FUEL PIPE SUB-ASSEMBLY

  1. Connect the fuel pipe.

    1. A071366E09
      Check that there is no damage or contamination in the connected part of the pipe.

    2. Align the axis of the connector with the axis of the pipe. Push the pipe into the connector until the connector makes a "click" sound. If the connection is tight, apply a little amount of fresh engine oil on the tip of the pipe.

    3. A071366E10
      After having finished the connection, try to pull apart the pipe and the connector and confirm that they are securely connected.

  1. Install the fuel pipe clamp.


4. CONNECT NO. 1 FUEL PIPE SUB-ASSEMBLY

  1. Connect the fuel pipe.

    1. A071366E09
      Check that there is no damage or contamination in the connected part of the pipe.

    2. Align the axis of the connector with the axis of the pipe. Push the pipe into the connector until the connector makes a "click" sound. If the connection is tight, apply a little amount of fresh engine oil on the tip of the pipe.

    3. A071366E10
      After having finished the connection, try to pull apart the pipe and the connector and confirm that they are securely connected.

  1. Install the fuel pipe clamp.


5. INSTALL INTAKE AIR SURGE TANK

A075648E01
  1. Install a new gasket and the surge tank with the 2 nuts.

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }

  1. Using an 8 hexagon wrench, install the 4 bolts.

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }

  1. A075647E01
    Install the 3 upper bolts which are used to secure the 2 surge tank stays and throttle body bracket.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }

  1. A075646E01
    Install the 3 wire harness clamps and hose clamp.

  1. Connect the throttle motor connector.

  1. Connect the 2 VSV connectors.

  1. A075645E01
    Connect the ventilation hose.

  1. A075644E01
    Connect the vapor feed hose assembly.

  1. A075598E01
    Connect the No. 4 water by-pass hose.

  1. A075597E01
    Connect the No. 5 water by-pass hose.


6. INSTALL AIR CLEANER ASSEMBLY

Torque:
8.0 N*m{ 82 kgf*cm , 71 in.*lbf }


7. CONNECT NO. 2 VENTILATION HOSE

A075594E01

8. INSTALL V-BANK COVER
  1. Install the cover with the 2 nuts.

    Torque:
    7.5 N*m{ 76.5 kgf*cm , 66 in.*lbf }


9. ADD ENGINE COOLANT
  1. Tighten all the plugs and fill the radiator with TOYOTA Super Long Life Coolant (SLLC).

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf } for cylinder block drain cock plug

    Standard capacity:
    Item
    Specified Condition
    A/T
    9.8 liters (10.4 US qts, 8.6 Imp. qts)
    M/T
    8.5 liters (9.0 US qts, 7.5 Imp. qts)

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic and technology consists of a combination of low phosphates and organic acids).
    2. Please contact your TOYOTA dealer for further details.

    NOTICE:
    Never use water as a substitute for engine coolant.

  1. Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.

  1. Install the radiator cap.

  1. Bleed air from the cooling system.

    1. Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.

    2. Maintain the engine speed at 2,000 to 2,500 rpm.

    3. Press the inlet and outlet radiator hoses several times by hand to bleed air.

      CAUTION:
      When pressing the radiator hoses:
      1. Wear protective gloves.
      2. Be careful as the radiator hoses are hot.
      3. Keep your hands away from the radiator fan.

  1. Stop the engine and wait until the coolant cools down to ambient temperature.

    CAUTION:
    Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. A112081E01
    Check the coolant level in the radiator reservoir.
    If the coolant level is low, add SLLC to the reservoir F line.


10. CONNECT CABLE TO BATTERY NEGATIVE TERMINAL

11. PERFORM INITIALIZATION
  1. Perform initialization (Click here).

    NOTICE:
    Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.


12. CHECK FOR FUEL LEAKS
  1. Connect the intelligent tester to the DLC3.

    1. Turn the ignition switch ON.

      NOTICE:
      Do not start the engine.

    2. Push the intelligent tester main switch ON.

    3. Select Active Test and enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

  1. Check for fuel leaks.

    1. Check that there are no fuel leaks after performing maintenance anywhere on the fuel system.

← INSPECTION (from Jun 2011)INSTALLATION (Aug 2012 – Jul 2013) →