2014 Hilux · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Jun 2011

NOTICE:
  1. When replacing the fuel supply pump, also replace the injection pipe.
  2. After removing the injection pipes and fuel inlet pipe, clean them with a brush and compressed air.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.


2. REMOVE NO. 1 ENGINE UNDER COVER
  1. Remove the 4 bolts and under cover.


3. REMOVE NO. 2 ENGINE UNDER COVER
  1. Remove the 4 bolts and under cover.


4. LOOSEN FUEL TANK CAP ASSEMBLY

5. DRAIN FUEL

6. DRAIN ENGINE COOLANT

NOTICE:
Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. A099591E01
    Drain the coolant by removing the reservoir cap and, using a wrench, remove the vent plug.

  1. Loosen the cylinder block drain cock plug and the radiator drain cock plug.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.


    A112147E01


7. DRAIN AUTOMATIC TRANSMISSION FLUID (for Automatic Transmission)

8. REMOVE RADIATOR ASSEMBLY
  1. Remove the radiator assembly (Click here).


9. REMOVE NO. 1 TIMING BELT COVER

A015094E01
  1. Remove the bolt and water hose clamp.

  1. Remove the wire harness clamp.

  1. Remove the 6 bolts and timing belt cover.


10. REMOVE TIMING BELT

A070549E02
  1. Turn the crankshaft clockwise and align the timing marks as shown in the illustration.

  1. A070550E01
    Uniformly loosen the 2 bolts and remove the timing belt tensioner.

  1. Remove the timing belt.

  1. Using a 10 mm hexagon wrench, remove the bolt, timing belt idler and washer.

    HINT:
    A070551E02
    1. When turning the camshaft while the timing belt is removed, turn the crankshaft 90° counterclockwise.
    2. When installing the timing belt, return the camshaft to the timing marks and then turn the crankshaft clockwise until it aligns with the timing marks, as shown in the illustration.


11. REMOVE FUEL SUPPLY PUMP

G036615E01
  1. Remove the bolt and clamp.

  1. Remove the 2 bolts and oil level gauge guide.

  1. A098969E05
    Using a 17 mm union nut wrench, loosen the union nuts and remove the fuel inlet pipe.

  1. A098895E01
    Disconnect the 2 fuel hoses.

  1. A098896E01
    Disconnect the 2 connectors.

  1. A070710E01
    Remove the 4 bolts indicated by the arrows in the illustration.

  1. Remove the No. 2 camshaft timing pulley flange and pump drive shaft pulley.

  1. A070711E02
    Remove the set nut and O-ring while holding the crankshaft pulley by using SST.
    SST
    09213-58013  
    09330-00021  

  1. A098897E01
    Loosen the 2 nuts.

  1. A070714E01
    Using SST, disconnect the pump from the injection gear.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)

    NOTICE:
    Apply lubricant to the threads and tip of SST (center bolt) before using it.

  1. Remove the 2 nuts and pump.

    NOTICE:
    1. Do not hold the pump or carry it holding the pipe.
    2. The pump must be kept horizontal.

  1. Remove the O-ring.

← COMPONENTS (from Jun 2011)INSPECTION (from Jun 2011) →