2014 Hilux · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built Jun 2011 – Jul 2012

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013

NOTICE:
  1. When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.
  2. When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.


1. INSTALL TIMING GEAR CASE ASSEMBLY
  1. Install 2 new O-rings to the cylinder block.

  1. Remove any old seal packing (FIPG material) from the timing gear case and cylinder block.

  1. A060151E03
    Install a new gasket to the timing gear case.

  1. A075511E07
    Apply seal packing as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Seal diameter:
    4 mm (0.15 in.)

    NOTICE:
    1. After applying seal packing, install the timing gear case within 3 minutes and tighten the bolts within 15 minutes.
    2. Do not start the engine for at least 2 hours after the installation.

  1. A060280E02
    Install the timing gear case with union bolt A and the 8 bolts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf } for bolt
    16 N*m{ 163 kgf*cm , 12 ft.*lbf } for union bolt A

  1. Make sure that the oil pump drive gear rotates smoothly.
    If the gear does not rotate smoothly, loosen the 8 bolts and union bolt and turn the gear. Then tighten the 8 bolts and union bolt and check the gear again.

  1. Install the No. 1 vacuum transmitting pipe with the nut.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }


2. INSTALL OIL STRAINER SUB-ASSEMBLY
  1. Install a new gasket and the oil strainer with the 2 bolts and nut.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }


3. INSTALL OIL PAN SUB-ASSEMBLY
  1. Remove any old seal packing (FIPG) from the oil pan and cylinder block.

  1. A151187E02
    Apply seal packing as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Seal diameter:
    4 mm (0.15 in.)

    NOTICE:
    1. After applying seal packing, install the oil pan within 3 minutes and tighten the bolts within 15 minutes.
    2. Do not start the engine for at least 2 hours after the installation.

  1. Install the oil pan with the 22 bolts and 2 nuts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }


4. INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE
  1. Apply clean engine oil to a new O-ring.

  1. Install the O-ring to the dipstick guide.

  1. Install the dipstick guide with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }


5. INSTALL ENGINE OIL LEVEL DIPSTICK

6. INSTALL FUEL SUPPLY PUMP ASSEMBLY

A070715E01
  1. Check that the injection gear in the timing gear case moves back and forth smoothly.

  1. Install a new O-ring to the pump.

  1. Apply a light coat of engine oil to the O-ring.

  1. A060835E01
    Align the set key on the drive shaft with the groove of the injection gear.

  1. A098897E01
    Install the pump with the 2 nuts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Set a new O-ring before tightening the set nut.

  1. A070711E01
    Using SST, hold the crankshaft pulley and install the set nut.
    SST
    09213-58013  
    09330-00021  

    Torque:
    64 N*m{ 653 kgf*cm , 47 ft.*lbf }

  1. A071144E01
    Move the pump drive shaft pulley back and forth to check the thrust clearance of the injection pump drive shaft.

    Thrust clearance:
    0.15 to 0.55 mm (0.0059 to 0.0217 in.)

    If the clearance is not within the specified range, disassemble and reassemble the supply pump and pump drive shaft pulley. Then repeat step above.

  1. A098896E01
    Connect the 2 connectors.

  1. A098895E01
    Connect the 2 fuel hoses.

  1. A098974E08
    Temporarily install the fuel inlet pipe with the union nuts.

    NOTICE:
    1. If the supply pump is replaced, the fuel inlet pipe must be replaced.
    2. Keep the fuel inlet pipe free of foreign matter.

  1. Using a 17 mm union nut wrench, tighten the injection pipe union nut on the common rail side.

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf } for use with union nut wrench
    35 N*m{ 357 kgf*cm , 26 ft.*lbf } for use without union nut wrench

    HINT:
    Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).

  1. Using a 17 mm union nut wrench, tighten the injection pipe union nut on the supply pump side.

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf } for use with union nut wrench
    35 N*m{ 357 kgf*cm , 26 ft.*lbf } for use without union nut wrench

    HINT:
    Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).

  1. Install the oil level gauge guide with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. G036615E01
    Install the clamp with the bolt.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }


7. INSTALL INJECTION GEAR

  1. A103270
    Install the injection gear and a new O-ring, and then temporarily install the nut. Using your hand, check the thrust clearance of the supply pump drive shaft by turning the injection gear.

    Standard thrust clearance:
    0.15 to 0.55 mm (0.0059 to 0.0217 in.)

    NOTICE:
    Fit the key (protrusion) of the supply pump to the key slot of the injection gear.

    HINT:
    If the clearance is not within the specified range, remove and reinstall the injection gear.


8. INSTALL CRANKSHAFT TIMING GEAR

  1. A103271E01
    Align the "1" timing marks of the oil pump drive gear and crankshaft timing gear as shown in the illustration.

  1. Using SST, install the crankshaft timing gear.

    SST
    09223-00010  


9. INSTALL NO. 1 IDLE GEAR

  1. A060159E05
    Install the No. 1 idle gear shaft to the cylinder block.

  1. A038763E01
    Apply a light coat engine oil to the No. 1 idle gear shaft shown in the illustration.

  1. G036757E01
    Align the "5" timing marks of the idle gear and crankshaft timing gear.

  1. Using SST, turn the supply pump gear, and align the "4" timing marks of the idle gear and injection gear, and mesh the gears.

    SST
    09960-10010   (09962-01000, 09963-00700)

  1. A060161E03
    Temporarily install the No. 1 idle gear and idle gear thrust plate with the 2 bolts.

    HINT:
    Face the thrust plate's protrusion outward.

  1. Secure the No. 2 idle gear to the No. 1 idle gear with a service bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Tighten the 2 bolts.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }

  1. Remove the service bolt.

  1. Install the No. 1 crankshaft sensor plate.


10. INSTALL TIMING GEAR COVER

  1. A072411E02
    Install a new O-ring to the timing gear case.

  1. Remove any old seal packing (FIPG material) from the timing gear cover.

  1. A075513E04
    Apply seal packing as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Seal diameter:
    4 mm (0.15 in.)

    NOTICE:
    1. After applying seal packing, install the gear cover within 3 minutes and tighten the bolts and nuts within 15 minutes.
    2. Do not start the engine for at least 2 hours after the installation.

  1. Install the cover with the 14 bolts and 2 nuts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

  1. Install the wire harness clamp.


11. INSTALL CRANKSHAFT POSITION SENSOR
  1. Install the crankshaft position sensor with the bolt.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }


12. INSTALL CAMSHAFT POSITION SENSOR
  1. Install the camshaft position sensor with the bolt.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }


13. INSTALL CRANKSHAFT PULLEY

A072417E02
  1. Align the pulley set key with the key groove of the pulley.

  1. Using SST, install the pulley bolt.

    SST
    09213-58014  
    09330-00021  

    Torque:
    365 N*m{ 3722 kgf*cm , 269 ft.*lbf }


14. INSTALL PUMP DRIVE SHAFT PULLEY
  1. Install a new O-ring to the supply pump.

  1. Temporarily install the supply pump with the nut.

  1. A070711E03
    Using SST, hold the crankshaft pulley and tighten the nut.
    SST
    09213-58014  
    09330-00021  

    Torque:
    64 N*m{ 653 kgf*cm , 47 ft.*lbf }

  1. A038747E01
    Install the No. 2 camshaft timing pulley flange and pump drive shaft pulley with the 4 bolts.

    Torque:
    31 N*m{ 316 kgf*cm , 23 ft.*lbf }

  1. A036609E01
    Using a dial indicator, check the thrust clearance of the pump drive shaft while moving the pump drive shaft pulley back and forth.

    Standard thrust clearance:
    0.15 to 0.55 mm (0.0059 to 0.0217 in.)

    If the clearance is not within the specified range, disassemble and reassemble the supply pump and pump drive shaft pulley. Then repeat the step above.


15. INSTALL VANE PUMP ASSEMBLY
  1. Install a new O-ring to the vane pump.

  1. Install the vane pump with the 2 nuts.

    Torque:
    41 N*m{ 418 kgf*cm , 30 ft.*lbf }


16. INSTALL VACUUM PUMP ASSEMBLY
  1. Install 2 new O-rings to the vacuum pump.

  1. Install the vacuum pump with the 2 nuts.

    Torque:
    21 N*m{ 210 kgf*cm , 15 ft.*lbf }


17. INSTALL WATER PUMP ASSEMBLY

A225339
  1. Install a new gasket and the water pump with the 5 bolts and 2 nuts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }


18. INSTALL NO. 2 TIMING BELT COVER

A060279E01
  1. Apply seal packing (FIPG) to the specified areas shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    NOTICE:
    After applying FIPG, install the No. 2 timing belt cover within 3 minutes and tighten its bolts and nut within 15 minutes.

  1. Install the No. 2 timing belt cover with the 4 bolts and nut.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


19. INSTALL NO. 1 TIMING BELT IDLER SUB-ASSEMBLY

20. INSTALL CAMSHAFT TIMING PULLEY

A060182E01
  1. Install the camshaft timing pulley.

  1. Fasten the bolt of the camshaft timing pulley by holding the camshaft with a wrench.

    Torque:
    98 N*m{ 1000 kgf*cm , 72 ft.*lbf }


21. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

  1. A272954E01
    Install 4 new No. 3 cylinder head cover gaskets to the cylinder head cover in the directions shown in the illustration.

    NOTICE:
    1. Do not install the No. 3 cylinder head cover gaskets at an angle.
    2. Check that there is no foreign matter at the installation location of the No. 3 cylinder head cover gaskets.

  1. Remove any old seal packing (FIPG) material from the cylinder head.

  1. A060179E03
    Apply seal packing to the specific areas shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the belt cover within 3 minutes after applying seal packing.
    3. Do not start the engine for at least 2 hours after installing the seal packing.

  1. Install a new cylinder head cover gasket and the cylinder head cover with the 10 bolts and 2 nuts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Install 4 new nozzle holder seals.

  1. Connect the 4 injector connectors.

  1. Connect the ventilation hose.


22. INSTALL FUEL INLET PIPE SUB-ASSEMBLY

  1. A098974E05
    Temporarily install the fuel inlet pipe with the union nuts.

    NOTICE:
    1. When replacing the common rail, it is necessary to replace the 4 injection pipes and fuel inlet pipe with new ones.
    2. Be careful that dust, dirt or any other foreign matter does not contact the joint area of the fuel inlet pipe.

  1. Using a 17 mm union nut wrench, tighten the fuel inlet pipe union nut on the common rail side.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).

  1. Using a 17 mm union nut wrench, tighten the fuel inlet pipe union nut on the supply pump side.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).

  1. Install a new O-ring to the engine oil level dipstick guide.

  1. Install the engine oil level dipstick guide with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Install the clamp with the bolt.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Install the engine oil level dipstick.


23. INSTALL NO. 4 INJECTION PIPE SUB-ASSEMBLY
  1. Temporarily install the No. 4 injection pipe with the union nuts.

  1. Install the 2 bolts.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }

    NOTICE:
    1. If an injection pipe clamp is removed from the No. 4 injection pipe, replace the injection clamp with a new one.
    2. Make sure that the inner-rubbers of the injection pipe fit inside the clamps.
    3. When installing the pipe, check that the inner-rubbers and the clamps are in their proper positions.

  1. A098973E03
    Using a 17 mm union nut wrench, tighten the injection pipe union nut on the common rail side.

    Torque:
    35 N*m{ 357 kgf*cm , 26 in.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).

  1. Using a 17 mm union nut wrench, tighten the injection pipe union nut on the injector side.

    Torque:
    35 N*m{ 357 kgf*cm , 26 in.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).


24. INSTALL NO. 1 INJECTION PIPE SUB-ASSEMBLY

NOTICE:
  1. When replacing an injector, it is necessary to replace the 4 injection pipes with new ones.
  2. Keep the joints of the injection pipe clean.

  1. G038585E04
    Temporarily install the No. 1, No. 2 and No. 3 injection pipes with the union nuts.

  1. Install the No. 2 and No. 3 injection pipe clamps with the bolt and 2 nuts, as shown in the illustration.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

    HINT:
    If the painted mark on the No. 1 injection pipe has disappeared, use the illustration as a reference to install the clamps.

  1. A098972E03
    Using a 17 mm union nut wrench, tighten the injection pipe union nuts on the common rail side.

    Torque:
    35 N*m{ 357 kgf*cm , 26 in.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).

  1. Using a 17 mm union nut wrench, tighten the injection pipe union nuts on the injector side.

    Torque:
    35 N*m{ 357 kgf*cm , 26 in.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).


25. INSTALL MANIFOLD STAY

  1. w/o EGR Cooler:

    1. A253486E01
      Install the stay with the 2 bolts.

      Torque:
      19 N*m{ 194 kgf*cm , 14 ft.*lbf }

      HINT:
      The manifold stay indented area (labeled A) must face the manifold.

  1. w/ EGR Cooler:

    1. A148131
      Install the manifold with the 2 bolts.

      Torque:
      19 N*m{ 194 kgf*cm , 14 ft.*lbf }

    2. Connect the 3 vacuum hoses and 2 VSV connectors.


26. INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

A097638E01
  1. Install the V-ribbed belt tensioner with the 4 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

    HINT:
    Firmly press and hold the tensioner against the cylinder block to eliminate any gaps in the areas labeled A in the illustration. Then uniformly tighten the 4 bolts.


27. INSTALL NO. 1 COMPRESSOR MOUNTING BRACKET
  1. Install the No. 1 compressor mounting bracket with the 4 bolts.

    Torque:
    45 N*m{ 459 kgf*cm , 33 ft.*lbf }


28. INSTALL GENERATOR BRACKET
  1. Install the generator bracket with the bolt.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }


29. INSTALL GENERATOR ASSEMBLY

A111821E01
  1. Install the generator with the 2 bolts.

    Torque:
    62 N*m{ 632 kgf*cm , 46 ft.*lbf } for bolt A
    25 N*m{ 255 kgf*cm , 18 ft.*lbf } for bolt B

  1. Install the generator wire with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Connect the generator connector.


30. INSTALL NO. 2 IDLE PULLEY ASSEMBLY

31. INSTALL NO. 1 VISCOUS HEATER BRACKET SUB-ASSEMBLY
  1. Install the No. 1 viscous heater bracket with the 2 bolts.

    Torque:
    45 N*m{ 459 kgf*cm , 33 ft.*lbf }


32. INSTALL VISCOUS WITH MAGNET CLUTCH HEATER ASSEMBLY

  1. I034100E02
    Install the viscous with magnet clutch heater with the 2 bolt.

    Torque:
    45 N*m{ 459 kgf*cm , 33 ft.*lbf }

  1. Connect the connect.


33. INSTALL TIMING BELT

  1. A070691E02
    Check that the timing marks are aligned as shown in the illustration.

    HINT:
    If reusing the timing belt, align the points marked during removal, and install the belt with the arrow pointing in the direction of engine revolution.

    NOTICE:
    1. The engine should be cold.
    2. When turning the crankshaft, the valve heads will hit against the piston's top position. Do not turn it more than necessary.

  1. Using a 10 mm hexagon wrench, install the timing belt idler pulley and new washer with the bolt.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }

  1. Check that the idler pulley moves smoothly.
    If it does not move smoothly, check the idler sub-assembly and washer.

  1. Install the timing belt to the pump drive shaft pulley, camshaft timing pulley and No. 1 timing belt idler in sequence.

  1. A070548E01
    Place the tensioner upright. Then set the press to the top of the tensioner.

    NOTICE:
    1. Do not scratch or deform the rod end.
    2. Press in the tensioner rod upward.
    3. Protect the tip of the push rod with a cloth in order to prevent damage.

  1. Using a press, slowly push in the push rod using 981 to 9800 N (100 to 999 kgf, 220 to 2203 lbf) of force.

    NOTICE:
    Do not impose a load of over 9800 N (100 to 999 kgf, 2203 lbf) to the push rod.

  1. Align the holes of the push rod and housing. Then pass a 1.27 mm hexagon wrench through the holes to keep the setting position of the push rod.

  1. Install the timing belt tensioner with the 2 bolts while pushing the idler pulley toward the timing belt.

  1. Tighten the 2 bolts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

    NOTICE:
    Uniformly tighten the 2 bolts and install the tensioner.

  1. A059983E01
    Remove the 1.5 mm hexagon wrench from the tensioner.

  1. A070549E02
    Turn the crankshaft clockwise 720° and check that the timing marks are aligned as shown in the illustration.


34. INSTALL NO. 1 TIMING BELT COVER
  1. Install the timing belt cover with the 6 bolts.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }

  1. Install the wire harness clamp.

  1. Install the water hose clamp with the bolt.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }


35. INSTALL ENGINE ASSEMBLY
  1. Install the engine (Click here).

← REASSEMBLY (from Jun 2011)INSTALLATION (Aug 2012 – Jul 2013) →