2014 Hilux · Service Manual BODY

REMOVAL

Removal / installation · Vehicles built from Aug 2013

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013

HINT:
  1. Use the same procedure for RHD and LHD vehicles.
  2. The procedure listed below is for LHD vehicles.
  3. Use the same procedure for the RH and LH sides.
  4. The procedure listed below is for the LH side.


1. PRECAUTION (w/ Power Window)

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Power Window)

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


3. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (w/ Power Window)

  1. B277019E01
    Using a moulding remover, detach the 2 clips.

  1. Disconnect the 4 claws and remove the power window regulator master switch assembly with front door armrest base panel.

    Text in Illustration 
    *A
    for Double Cab
    *B
    for Single Cab, for Extra Cab


4. REMOVE FRONT DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)

  1. B277021E01
    Insert a clip remover between the plate and trim board.

    HINT:
    Tape the clip remover tip before use.

    Text in Illustration 
    *1
    Protective Tape

  1. Turn the handle counterclockwise to remove the snap ring, front door window regulator handle and plate.


5. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH

  1. B277018E01
    Detach the 2 clips and remove the front door lower frame bracket garnish.
    Text in Illustration 
    *A
    w/o Front No. 2 Speaker
    *B
    w/ Front No. 2 Speaker


6. REMOVE DOOR PULL HANDLE

  1. B277022
    Remove the screw and door pull handle.


7. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

  1. B277024E01
    for Double Cab:

    1. Remove the clip and screw.

      Text in Illustration 
      *1
      Clip
      *2
      Screw

    2. Detach the 8 clips and remove the front door trim board.

  1. B277023E01
    for Single Cab, for Extra Cab:

    1. Remove the clip and screw.

      Text in Illustration 
      *1
      Clip
      *2
      Screw

    2. Detach the 9 clips and remove the front door trim board.


8. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY LH

B113822
  1. w/ Power Mirror Control System:
    Disconnect the mirror connector.

  1. Remove the 3 nuts.

  1. Push down the claw and remove the outer rear view mirror assembly LH.


9. REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY LH

  1. B277027E01
    Detach the claw and 2 guides as indicated by the arrows in the order shown in the illustration.

  1. B277028
    Disconnect the front door inside locking cable and front door lock remote control cable and remove the front door inside handle.


10. REMOVE FRONT DOOR NO. 1 TRIM BRACKET

  1. B277026
    Remove the 2 screws and front door No. 1 trim bracket.


11. REMOVE FRONT DOOR SERVICE HOLE COVER LH

  1. B281060
    Pull out the front door inside locking cable, front door lock remote control cable and wire harness from the front door service hole cover, and then remove the front door service hole cover.

    HINT:
    Remove any remaining butyl tape from the front door panel.


12. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH
  1. w/ Power Window:

    1. Temporarily install the power window regulator master switch assembly with front door armrest base panel.

    2. Connect the cable to the negative (-) battery terminal.

    3. Move the front door glass sub-assembly so that the front door glass bolts can be seen.

    4. Disconnect the cable from the negative (-) battery terminal.

      NOTICE:
      When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

    5. Remove the power window regulator master switch assembly with front door armrest base panel.

  1. w/o Power Window:

    1. Temporarily install the door window regulator handle.

    2. Move the front door glass sub-assembly so that the front door glass bolts can be seen.

    3. Remove the door window regulator handle.

  1. B277030
    Remove the 2 bolts.

    NOTICE:
    After the bolts are removed, do not allow the front door glass to fall.

  1. B277031E01
    Remove the front door glass as indicated by the arrows in the order shown in the illustration.

    NOTICE:
    Do not damage the front door glass.


13. REMOVE FRONT DOOR OUTER GLASS WEATHERSTRIP ASSEMBLY LH

  1. B278240E01
    Put protective tape around the front door outer glass weatherstrip.
    Text in Illustration 
    *A
    for Double Cab
    *B
    for Single Cab, for Extra Cab
    *1
    Protective Tape

  1. Detach the 5 claws and remove the front door outer glass weatherstrip.

← REMOVAL (Aug 2012 – Jul 2013)INSTALLATION (Jun 2011 – Jul 2012) →