2014 Hilux · Service Manual BODY ELECTRICAL

INSPECTION

Inspection · Vehicles built from Jun 2011


INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY (for LHD)
SST
09843-18040  

  1. B113575E01
    Measure the resistance of the switch.

    Standard resistance (Windshield wiper switch):
    Tester Connection
    Switch Condition
    Specified Condition
    B-3 (+1) - B-2 (+B)
    MIST
    Below 1 Ω
    B-3 (+1) - B-1 (+S)
    OFF
    Below 1 Ω
    B-3 (+1) - B-1 (+S)
    INT
    Below 1 Ω
    B-3 (+1) - B-2 (+B)
    LO
    Below 1 Ω
    B-4 (+2) - B-2 (+B)
    HI
    Below 1 Ω

    Standard resistance (Windshield washer switch):
    Tester Connection
    Switch Condition
    Specified Condition
    A-3 (WF) -A-2 (EW)
    OFF
    10 kΩ or higher
    A-3 (WF) -A-2 (EW)
    ON
    Below 1 Ω

    If the result is not as specified, replace the switch assembly.

  1. Check the intermittent operation.

    1. Connect the voltmeter's positive (+) lead to terminal B-3 (+1) and the negative (-) lead to terminal A-2 (EW).

    2. Connect the battery's positive (+) lead to terminal B-2 (+B) and the negative (-) lead to terminals A-2 (EW) and B-1 (+S).

    3. Turn the wiper switch to the INT position.

    4. Connect the battery's positive (+) lead to terminal B-1 (+S) for 5 seconds.

    5. Connect the battery's negative (-) lead to terminal B-1 (+S). Operate the intermittent wiper relay and check the voltage between terminals B-3 (+1) and A-2 (EW).

      OK:
      Refer to illustration below.


      E056399E04
      If the result is not as specified, replace the switch assembly.

  1. Check the washer operation.

    1. Turn the wiper switch OFF.

    2. Connect the battery's positive (+) lead to terminal B-2 (+B) and the negative (-) lead to terminals B-4 (+S) and A-2 (EW).

    3. Connect the voltmeter's positive (+) lead to terminal B-2 (+1) and the negative (-) lead to terminal A-2 (EW).

    4. Turn the washer switch ON and OFF, and check the voltage between terminals B-2 (+1) and A-2 (EW).

      OK:
      Refer to illustration below.


      B086335E02
      If the result is not as specified, replace the switch assembly.


INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY (for RHD)
SST
09843-18040  

  1. B086316E01
    for Except Europe:

    1. Measure the resistance of the switch.

      Standard resistance (Windshield wiper switch):
      Tester Connection
      Switch Condition
      Specified Condition
      B-2 (+1) - B-3 (+B)
      MIST
      Below 1 Ω
      B-2 (+1) - B-4 (+S)
      OFF
      Below 1 Ω
      B-2 (+1) - B-4 (+S)
      INT
      Below 1 Ω
      B-2 (+1) - B-3 (+B)
      LO
      Below 1 Ω
      B-1 (+2) - B-3 (+B)
      HI
      Below 1 Ω

      Standard resistance (Windshield washer switch):
      Tester Connection
      Switch Condition
      Specified Condition
      A-1 (WF) -A-2 (EW)
      OFF
      10 kΩ or higher
      A-1 (WF) -A-2 (EW)
      ON
      Below 1 Ω

      If the result is not as specified, replace the switch assembly.

    2. Check the intermittent operation.

      1. Connect the voltmeter's positive (+) lead to terminal B-2 (+1) and the negative (-) lead to terminal A-2 (EW).
      2. Connect the battery's positive (+) lead to terminal B-3 (+B) and the negative (-) lead to terminals A-2 (EW) and B-4 (+S).
      3. Turn the wiper switch to the INT position.
      4. Connect the battery's positive (+) lead to terminal B-4 (+S) for 5 seconds.

      5. Connect the battery's negative (-) lead to terminal B-4 (+S). Operate the intermittent wiper relay and check the voltage between terminals B-2 (+1) and A-2 (EW).

        OK:
        Refer to illustration below.


        E056399E05
        If the result is not as specified, replace the switch assembly.

    3. Check the washer operation.

      1. Turn the wiper switch OFF.
      2. Connect the battery's positive (+) lead to terminal B-2 (+B) and the negative (-) lead to terminals B-4 (+S) and A-2 (EW).
      3. Connect the voltmeter's positive (+) lead to terminal B-2 (+1) and the negative (-) lead to terminal A-2 (EW).

      4. Turn the washer switch ON and OFF, and check the voltage between terminals B-2 (+1) and A-2 (EW).

        OK:
        Refer to illustration below.


        B086335E01
        If the result is not as specified, replace the switch assembly.

  1. for Europe:

    1. B113575E01
      Measure the resistance of the switch.

      Standard resistance (Windshield wiper switch):
      Tester Connection
      Switch Condition
      Specified Condition
      B-3 (+1) - B-2 (+B)
      MIST
      Below 1 Ω
      B-3 (+1) - B-1 (+S)
      OFF
      Below 1 Ω
      B-3 (+1) - B-1 (+S)
      INT
      Below 1 Ω
      B-3 (+1) - B-2 (+B)
      LO
      Below 1 Ω
      B-4 (+2) - B-2 (+B)
      HI
      Below 1 Ω

      Standard resistance (Windshield washer switch):
      Tester Connection
      Switch Condition
      Specified Condition
      A-3 (WF) -A-2 (EW)
      OFF
      10 kΩ or higher
      A-3 (WF) -A-2 (EW)
      ON
      Below 1 Ω

      If the result is not as specified, replace the switch assembly.

    2. Check the intermittent operation.

      1. Connect the voltmeter's positive (+) lead to terminal B-3 (+1) and the negative (-) lead to terminal A-2 (EW).
      2. Connect the battery's positive (+) lead to terminal B-2 (+B) and the negative (-) lead to terminals A-2 (EW) and B-1 (+S).
      3. Turn the wiper switch to the INT position.
      4. Connect the battery's positive (+) lead to terminal B-1 (+S) for 5 seconds.

      5. Connect the battery's negative (-) lead to terminal B-1 (+S). Operate the intermittent wiper relay and check the voltage between terminals B-3 (+1) and A-2 (EW).

        OK:
        Refer to illustration below.


        E056399E04
        If the result is not as specified, replace the switch assembly.

    3. Check the washer operation.

      1. Turn the wiper switch OFF.
      2. Connect the battery's positive (+) lead to terminal B-2 (+B) and the negative (-) lead to terminals B-4 (+S) and A-2 (EW).
      3. Connect the voltmeter's positive (+) lead to terminal B-2 (+1) and the negative (-) lead to terminal A-2 (EW).

      4. Turn the washer switch ON and OFF, and check the voltage between terminals B-2 (+1) and A-2 (EW).

        OK:
        Refer to illustration below.


        B086335E02
        If the result is not as specified, replace the switch assembly.

← REMOVAL (from Aug 2013)INSTALLATION (Jun 2011 – Jul 2012) →