2014 Hilux · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Aug 2013

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013


1. DISCONNECT BATTERY NEGATIVE TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.


2. DISCHARGE FUEL SYSTEM PRESSURE

CAUTION:
  1. Do not disconnect any part of the fuel system until you have discharged the fuel system pressure.
  2. Even after discharging the fuel pressure, place a cloth or equivalent over fittings as you separate them to reduce risk of fuel spray on yourself or in the engine compartment.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.

  1. G038856E01
    Disconnect the fuel pump connector.

  1. Connect the cable to the negative (-) battery terminal.

  1. Start the engine. After the engine has stopped on its own, turn the ignition switch OFF.

    HINT:
    DTC P0171/25 (system too lean) may be set.

  1. Crank the engine again, then check that the engine does not start.

  1. Loosen the fuel tank cap, then discharge the pressure in the fuel tank completely.

  1. Connect the fuel pump connector.


3. DRAIN ENGINE COOLANT
  1. Remove the radiator cap.

  1. Loosen the cylinder block drain cock plug and radiator drain plug, and then the coolant.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.


    A270641E01


4. REMOVE DRIVE BELT

A076441E01
  1. While releasing the belt tension by turning the belt tensioner counterclockwise, remove the V-ribbed belt from the belt tensioner.


5. REMOVE V-BANK COVER

  1. A112983
    Remove the 2 nuts and the V-bank cover.


6. REMOVE NO. 2 VENTILATION HOSE

A075594

7. REMOVE AIR CLEANER

  1. A075595
    Disconnect the vacuum hose.

  1. Disconnect the MAF meter connector.

  1. Remove the 2 wire harness clamps.

  1. A075596
    Loosen the 2 hose clamps.

  1. Remove the 2 bolts and air cleaner.


8. REMOVE INTAKE AIR SURGE TANK

A076500E02
  1. Disconnect the 2 water by-pass hoses.

  1. A075644E01
    Disconnect the purge line hose.

  1. A075645E01
    Disconnect the ventilation hose.

  1. A075646E01
    Disconnect the 2 VSV connectors.

  1. Disconnect the throttle body with motor connector.

  1. Separate the 3 wire harness clamps and hose clamp.

  1. A076501E01
    Remove the 2 bolts and throttle body bracket.

  1. A076502E01
    Remove the bolt and oil baffle plate.

  1. Remove the 4 bolts and 2 surge tank stays.

  1. A075648E01
    Remove the 2 nuts.

  1. Using an 8 mm hexagon socket wrench, remove the 4 bolts, intake air surge tank and gasket.


9. REMOVE IGNITION COIL

10. REMOVE CYLINDER HEAD COVER RH

  1. A072943E01
    Remove the 10 bolts, 3 seal washers, 2 nuts, cylinder head cover and gasket.


11. REMOVE CYLINDER HEAD COVER LH

  1. A076503E01
    Remove the 10 bolts, 3 seal washers, 2 nuts, cylinder head cover and gasket.


12. SET NO. 1 CYLINDER TO TDC/COMPRESSION

  1. A076530E01
    Turn the crankshaft pulley, and align the notch with timing mark 0 of the timing chain cover.

  1. G038065E02
    Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the bearing cap as shown in the illustration.
    If the timing marks are not aligned, turn the crankshaft 1 complete revolution (360°) and align the timing marks as stored above.

  1. G038066E01
    Place paint marks on the No. 1 chain links that correspond with the timing marks of the camshaft timing gears.


13. REMOVE NO. 1 CHAIN TENSIONER

NOTICE:
  1. Never rotate the crankshaft with the chain tensioner removed.
  2. When rotating the camshaft with the timing chain removed, rotate the crankshaft counterclockwise 40° from the TDC first.

  1. A076506E01
    Remove the 4 bolts, timing chain cover plate and gasket.

  1. A072958E01
    While turning the stopper plate of the tensioner clockwise, push in the plunger of the chain tensioner as shown in the illustration.

  1. While turning the stopper plate of the tensioner counterclockwise, insert a diameter of 3.5 mm (0.138 in.) bar into the holes on the stopper plate and tensioner to fix the stopper plate.

  1. Remove the 2 bolts and chain tensioner.


14. REMOVE NO. 2 CAMSHAFT

NOTICE:
As the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being removed. If the camshaft is not kept level, the portion of the cylinder head which receives the shaft thrust may crack or be damaged, causing the camshaft to seize or break. To avoid this, the following steps should be carried out.

  1. G038067E01
    While raising up the No. 2 chain tensioner, insert a diameter of 1.0 mm (0.039 in.) into the hole to fix it.

  1. G038068E01
    Hold the hexagonal portion of the No. 2 camshaft with a wrench, and remove the camshaft timing gear set bolt.

    NOTICE:
    Be careful not to damage the cylinder head and valve lifter with the wrench.

  1. Separate the camshaft timing gear from the No. 2 camshaft.

  1. G038069E01
    Rotate the camshaft counterclockwise using the wrench so that the cam lobes of No. 1 cylinder faces upward as shown in the illustration.

  1. A076510E01
    Uniformly loosen and remove the 8 bearing cap bolts in several passes in the sequence shown in the illustration.

  1. Remove the 4 bearing caps and No. 2 camshaft.


15. REMOVE NO. 2 CHAIN TENSIONER

  1. G038070E01
    Remove the No. 2 chain tensioner bolt, and then remove the No. 2 chain tensioner and camshaft timing gear.


16. REMOVE NO. 1 CAMSHAFT

NOTICE:
As the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being removed. If the camshaft is not kept level, the portion of the cylinder head which receives the shaft thrust may crack or be damaged, causing the camshaft to seize or break. To avoid this, the following steps should be carried out.

  1. G038072E01
    Hold the hexagonal portion of the No. 1 camshaft with a wrench, and loosen the camshaft timing gear set bolt.

    NOTICE:
    1. Be careful not to damage the cylinder head and valve lifter with the wrench.
    2. Do not disassemble the camshaft timing gear assembly.

  1. G038071E01
    Slide the camshaft timing gear and separate the No. 1 chain from the camshaft timing gear.

  1. G038073E01
    Rotate the No. 1 camshaft counterclockwise using the wrench so that the cam lobes of No. 1 cylinder faces downward as shown in the illustration.

  1. A076515E01
    Loosen and remove the 8 bearing cap bolts in several passes in the sequence shown in the illustration.

  1. Remove the 4 bearing caps.

  1. G038074E01
    Remove the camshaft timing gear set bolt with the No. 1 camshaft is lifted up, and then remove the No. 1 camshaft and camshaft timing gear with No. 2 chain.

  1. A076517E01
    Tie the No. 1 chain with a string as shown in the illustration.

    NOTICE:
    Be careful not to drop anything inside the timing chain cover.

← REMOVAL (Aug 2012 – Jul 2013)INSPECTION (from Jun 2011) →