2014 Hilux · Service Manual ENGINE

INSPECTION

Inspection · Vehicles built from Aug 2013

Versions by build date: Jun 2011 – Jul 2013 from Aug 2013


INSPECT STARTER ASSEMBLY

CAUTION:
As a large electric current passes through the cable during this inspection, a thick cable must be used. If not, the cable may become hot and cause injury.

NOTICE:
The following tests must be done within 3 to 5 seconds to prevent the coil from burning out.

  1. Mount the starter assembly in a vise between aluminum plates.

  1. Perform the pull-in test.

    1. A221352
      Remove the nut and disconnect the lead wire from terminal C.

    2. A221364E01
      Connect the battery to the magnet starter switch as shown in the illustration. Check that the clutch pinion gear extends.
      Text in Illustration 
      *1
      Terminal C
      *2
      Terminal 50
      V100135
      Move
      If the clutch pinion gear does not move, replace the magnet starter switch assembly.

  1. Perform the holding test.

    1. A221365E01
      Maintain the battery connections of the pull-in test above, but disconnect the negative (-) lead from terminal C. Check that the pinion gear remains extended.
      Text in Illustration 
      *1
      Terminal C
      V100135
      Disconnect
      If the clutch pinion gear returns inward, replace the magnet starter switch assembly.

  1. Inspect the clutch pinion gear return.

    1. A300400
      Disconnect the negative (-) lead from the starter body. Check that the clutch pinion gear returns.
      Text in Illustration 
      V100135
      Disconnect
      V100136
      Move
      If the clutch pinion gear does not return, replace the magnet starter switch assembly.

  1. Perform the no-load performance test.

    1. Connect the lead wire to terminal C with the nut. Make sure that the lead wire is not grounded.

      Torque:
      10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    2. Mount the starter assembly in a vise between aluminum plates.

    3. A227340E01
      Connect the battery and an ammeter probe to the starter as shown in the illustration.
      Text in Illustration 
      *1
      Terminal 30
      *2
      Terminal 50
      *3
      Ammeter Probe
      V100135
      Move

    4. Check that the starter rotates smoothly and steadily while the pinion gear is moving out. Then measure the current.

      Standard current:
      90 A or less at 11.5 V

      If the result is not as specified, replace the starter assembly.


INSPECT STARTER ARMATURE ASSEMBLY
  1. Check the commutator for dirt and/or burns on the surface.
    If the surface is dirty or burnt, correct it with 400-grit sandpaper or a lathe.

  1. A122065E03
    Inspect the commutator for an open circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Segment - Segment
      Always
      Below 1 Ω

      Text in Illustration 
      *1
      Segment
      If the result is not as specified, replace the starter armature assembly.

  1. A122066E03
    Inspect the commutator for a short circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Segment - Armature coil core
      Always
      10 kΩ or higher

      Text in Illustration 
      *1
      Segment
      *2
      Armature Coil Core
      If the result is not as specified, replace the starter armature assembly.

  1. A300395
    Using a vernier caliper, measure the commutator diameter.

    Standard diameter:
    29.0 mm (1.14 in.)

    Minimum diameter:
    28.0 mm (1.10 in.)

    If the diameter is less than the minimum, replace the starter armature assembly.

  1. A122067
    Check the commutator circle runout.

    1. Place the shaft of the starter armature on V-blocks.

    2. Using a dial indicator, measure the circle runout.

      Maximum commutator runout:
      0.05 mm (0.00197 in.)

      If the runout is more than the maximum, replace the starter armature assembly.

  1. A115027
    Measure the undercut depth of the commutator.

    Standard undercut depth:
    0.7 mm (0.0276 in.)

    Minimum undercut depth:
    0.2 mm (0.00787 in.)

    If the undercut depth is less than the minimum, correct it with a hacksaw blade.


INSPECT STARTER BRUSH HOLDER ASSEMBLY

  1. Using a vernier caliper, measure the brush length.

    A300396E01

    Text in Illustration 
    *1
    Brush
    *2
    Spring
    *3
    Length
    -
    -

    Standard length:
    14.4 mm (0.567 in.)

    Minimum length:
    9.0 mm (0.354 in.)

    If the length is less than the minimum, replace the starter brush holder assembly and starter yoke assembly.

  1. ST00019E15
    Inspect the load of the brush spring.

    1. Take a pull scale reading immediately after the brush spring separates from the brush.

      Standard spring load:
      16 to 20 N (1.7 to 2.0 kgf, 3.6 to 4.5 lbf)

      Minimum spring load:
      6.7 N (0.7 kgf, 1.5 lbf)

      Text in Illustration 
      *1
      Brush
      *2
      Brush Spring
      If the load is less than the minimum, replace the starter brush holder assembly.


INSPECT STARTER BRUSH HOLDER ASSEMBLY

  1. A300397E01
    Inspect the insulation.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Positive brush holder - Negative brush holder
      Always
      10 kΩ or higher

      If the result is not as specified, replace the starter brush holder assembly.


INSPECT STARTER CENTER BEARING CLUTCH SUB-ASSEMBLY
  1. Check the gear teeth of the planetary gears and starter center bearing clutch for wear or damage.
    If any planetary gear is damaged, replace the planetary gear assembly.
    If any gear of the starter center bearing clutch is damaged, replace the starter center bearing clutch sub-assembly.

  1. A221357
    Check the movement of the clutch pinion gear.
    Text in Illustration 
    V100135
    Free
    V100136
    Lock

    1. Rotate the clutch pinion gear clockwise and check that it turns freely.

    2. Try to rotate the clutch pinion gear counterclockwise and check that it locks.
      If the clutch pinion gear cannot be turned clockwise smoothly, or does not lock in the counterclockwise direction, replace the starter center bearing clutch sub-assembly.


INSPECT MAGNET STARTER SWITCH ASSEMBLY

  1. A300398
    Push in the plunger and check that it returns quickly to its original position.
    If the result is not as specified, replace the magnet starter switch assembly.

  1. A194284E04
    Check the pull-in coil for an open circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Terminal 50 - Terminal C
      Always
      Below 1 Ω

      Text in Illustration 
      *1
      Terminal 50
      *2
      Terminal C
      If the result is not as specified, replace the magnet starter switch assembly.

  1. A194285E04
    Check the holding coil for an open circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Terminal 50 - Switch body
      Always
      Below 2 Ω

      Text in Illustration 
      *1
      Terminal 50
      *2
      Switch Body
      If the result is not as specified, replace the magnet starter switch assembly.

← INSPECTION (Jun 2011 – Jul 2013)REASSEMBLY (Jun 2011 – Jul 2013) →