P0405 Exhaust Gas Recirculation Sensor "A" Circuit Low
Diagnostic trouble codes · Vehicles built Aug 2012 – Jul 2013
Also covers:
- P0406 Exhaust Gas Recirculation Sensor "A" Circuit High
Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
The EGR valve position sensor is mounted on the EGR valve and used for detecting the EGR valve angle. The EGR valve angle detected by the sensor is sent to the ECM as feedback. The ECM then regulates the EGR valve angle in accordance with engine running conditions.| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
| Ignition switch ON for 5 seconds |
EGR valve position sensor output voltage is less than 0.2 V for 2 seconds. (1 trip detection logic) |
|
| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
| Ignition switch ON for 5 seconds |
EGR valve position sensor output voltage is higher than 4.8 V for 2 seconds. (1 trip detection logic) |
|
MONITOR DESCRIPTION
When the output voltage of the EGR valve position sensor deviates from the normal operating range of 0.1 to 4.9 V for more than 5 seconds, the ECM interprets this as a malfunction of the sensor circuit and illuminates the MIL.WIRING DIAGRAM
Refer to DTC P042E (Click here).INSPECTION PROCEDURE
- NOTICE:
- Inspect the fuses of circuits related to this system before performing the following inspection procedure.
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
- After replacing the fuel supply pump assembly, the ECM needs initialization (Click here).
- After replacing an injector assembly, the ECM needs registration (Click here).
- Inspect the fuses of circuits related to this system before performing the following inspection procedure.
- HINT:
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
| 1. CHECK HARNESS AND CONNECTOR (EGR VALVE POSITION SENSOR - ECM) |
Disconnect the electric EGR control valve assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
E28-3 (VC) - E27-13 (VC)
Always
Below 1 Ω
E28-2 (VTA) - E26-1 (EGRA)
Always
Below 1 Ω
E28-1 (E2) - E27-14 (E2)
Always
Below 1 Ω
E28-3 (VC) or E27-13 (VC) - Body ground
Always
10 kΩ or higher
E28-2 (VTA) or E26-1 (EGRA) - Body ground
Always
10 kΩ or higher
Reconnect the electric EGR control valve assembly connector.
Reconnect the ECM connector.
|
|
||||
| OK | |
| 2. CHECK HARNESS AND CONNECTOR (POWER SOURCE) |
Disconnect the electric EGR control valve assembly connector.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
E28-3 (VC) - E28-1 (E2)
Ignition switch ON
4.5 to 5.5 V
Text in Illustration *a
Front view of wire harness connector
(to Electric EGR Valve Assembly)
Reconnect the electric EGR control valve assembly connector.
|
|
||||
| OK | |
| 3. REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY |
Replace the electric EGR control valve assembly (Click here).
| NEXT | |
| 4. CHECK WHETHER DTC OUTPUT RECURS (P0405 OR P0406) |
Connect the intelligent tester to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch to ON for 5 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Confirm that the DTC is not output again.
- OK:
- DTC is not output again.
|
|
||||
| OK | ||
| ||
| 5. REPLACE ECM |
Replace the ECM (Click here).
|
|
||||
| 6. REPAIR OR REPLACE HARNESS OR CONNECTOR |
Repair or replace the harness or connector.
| NEXT | |
| 7. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the intelligent tester to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch to ON for 5 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Confirm that the DTC is not output again.
| NEXT | ||
| ||
