2014 Hilux · Service Manual ENGINE

P0106 Manifold Absolute Pressure / Barometric Pressure Circuit Range / Performance Problem

Diagnostic trouble codes · Vehicles built from Aug 2014

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

Refer to DTC P0107 (Click here).
P0106 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
After warming up engine, idle engine for 10 seconds or more, and then drive vehicle under load (accelerator opening amount 15% or more) with engine speed at 6000 rpm or less for 10 seconds
Either condition is met (2 trip detection logic):
(a) The manifold absolute pressure output is 1.66 V or higher for 10 seconds when idling the engine after warming it up.
(b) The manifold absolute pressure sensor output is 0.48 V or less for 10 seconds when the accelerator opening amount is 15% or more and the engine speed is 6000 rpm or less.
  1. Vacuum hose connection
  2. Manifold absolute pressure sensor
Related Data List 
DTC No.
Data List
P0106
MAP

HINT:
  1. If DTC P0106 is stored, the following symptoms may appear:
    1. Misfire
    2. Combustion noise
    3. Black smoke
    4. White smoke
    5. Lack of power


INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses of circuits related to this system before performing the following inspection procedure.
  2. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
  3. After replacing the fuel supply pump assembly, the ECM needs initialization (Click here).
  4. After replacing an injector assembly, the ECM needs registration (Click here).

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P0106)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    P0106 is output
    A
    P0106 and other DTCs are output
    B



B
GO TO DTC CHART (Click here)
A


2. CHECK VACUUM HOSE CONNECTIONS
  1. Check the vacuum hose connections.

    OK:
    Vacuum hose is connected correctly and is not damaged.



NG
Go to step 4
OK


3. REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
  1. Replace the manifold absolute pressure sensor.



NEXT
Go to step 5
4. CONNECT HOSE CORRECTLY

NEXT


5. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the intelligent tester to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off for 30 seconds or more.

  1. Start the engine.

  1. After warming up the engine, idle the engine for 10 seconds or more, and then drive the vehicle under load (accelerator opening angle 15% or more) with the engine speed at 6000 rpm or less for 10 seconds or more.

  1. Confirm that the pending DTC is not output again.

    HINT:
    Perform the following procedure using the tester to determine whether or not the DTC judgment has been carried out.

    1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

    2. Input DTC P0106.

    3. Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, drive the vehicle for 5 minutes, idle the engine for 5 minutes, and then check "All Readiness" again.


NEXT

END


← P0106 Manifold Absolute Pressure / Barometric Pressure Circuit Range / Performance Problem (Aug 2013 – Jul 2014)P0107 Manifold Absolute Pressure / Barometric Pressure Circuit Low Input (+ P0108) (Jun 2011 – Jul 2012) →