P0180 Fuel Temperature Sensor "A" Circuit
Diagnostic trouble codes · Vehicles built Jun 2011 – Jul 2012
Also covers:
- P0182 Fuel Temperature Sensor "A" Circuit Low Input
- P0183 Fuel Temperature Sensor "A" Circuit High Input
Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
The fuel temperature sensor monitors the fuel temperature. The fuel temperature sensor has a thermistor that varies its resistance depending on the fuel temperature. When the fuel temperature is low, the resistance of the thermistor is high. When the temperature is high, the resistance is low. The variations of resistance are communicated to the ECM as changes of voltage (See Fig. 1).The fuel temperature sensor is connected to the ECM. The 5 V power source voltage in the ECM is applied to the fuel temperature sensor from terminal THF via resistor R.
Resistor R and the fuel temperature sensor are connected in series. When the resistance value of the fuel temperature sensor changes due to a change in fuel temperature, the voltage at terminal THF also changes. Based on this signal, the ECM corrects the pressure control compensation of the fuel supply pump assembly.


| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
| Ignition switch ON for 0.5 seconds |
Open or short in the fuel temperature sensor circuit for 0.5 seconds (1 trip detection logic). |
|
| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
| Ignition switch ON for 0.5 seconds |
Short in the fuel temperature sensor circuit for 0.5 seconds (1 trip detection logic). |
|
| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
| Ignition switch ON for 0.5 seconds |
Open in the fuel temperature sensor circuit for 0.5 seconds (1 trip detection logic). |
|
| DTC No. |
Data List |
| P0180 |
Fuel Temp |
| P0182 | |
| P0183 |
- HINT:
- If DTC P0180, P0182 and/or P0183 is stored, the following symptoms may appear:
- Misfire
- Combustion noise
- Black smoke
- Lack of power
- If DTC P0180, P0182 and/or P0183 is stored, the following symptoms may appear:
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- Inspect the fuses of circuits related to this system before performing the following inspection procedure.
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
- After replacing the fuel supply pump assembly, the ECM needs initialization (Click here).
- After replacing an injector assembly, the ECM needs registration (Click here).
- Inspect the fuses of circuits related to this system before performing the following inspection procedure.
- HINT:
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
| 1. READ VALUE USING INTELLIGENT TESTER (FUEL TEMPERATURE) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Temp.
Read the value.
- OK:
- Same as the actual fuel temperature
Result Result
Proceed to
-40°C (-40°F)
A
140°C (284°F) or higher
B
OK (Same as actual fuel temperature)
C
- HINT:
- If there is an open circuit, the tester indicates -40°C (-40°F).
- If there is a short circuit, the tester indicates 140°C (284°F) or higher.
- If there is an open circuit, the tester indicates -40°C (-40°F).
|
|
||||
|
|
||||
| A | |
| 2. READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS) |
Disconnect the fuel temperature sensor connector.

Connect terminals 2 and 1 of the fuel temperature sensor connector.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Temp.
Read the value.
- OK:
- 140°C (284°F) or higher
Text in Illustration *1
Fuel Temperature Sensor
*2
ECM
*a
Front view of wire harness connector
(to Fuel Temperature Sensor)
Reconnect the fuel temperature sensor connector.
|
|
||||
| OK | |
| 3. REPLACE FUEL SUPPLY PUMP ASSEMBLY (FUEL TEMPERATURE SENSOR) |
Replace the fuel supply pump assembly (fuel temperature sensor) (Click here).
|
|
||||
| 4. CHECK HARNESS AND CONNECTOR (FUEL TEMPERATURE SENSOR - ECM) |
Disconnect the fuel temperature sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
F11-2 - E26-4 (THF)
Always
Below 1 Ω
F11-1 - E27-14 (E2)
Always
Below 1 Ω
Reconnect the fuel temperature sensor connector.
Reconnect the ECM connector.
|
|
||||
| OK | |
| 5. CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM. |
Replace the ECM (Click here).
|
|
||||
| 6. READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS) |
Disconnect the fuel temperature sensor connector.

Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Temp.
Read the value.
- OK:
- -40°C (-40°F)
Text in Illustration *1
Fuel Temperature Sensor
*2
ECM
Reconnect the fuel temperature sensor connector.
|
|
||||
| OK | |
| 7. REPLACE FUEL SUPPLY PUMP ASSEMBLY (FUEL TEMPERATURE SENSOR) |
Replace the fuel supply pump assembly (fuel temperature sensor) (Click here).
|
|
||||
| 8. CHECK HARNESS AND CONNECTOR (FUEL TEMPERATURE SENSOR - ECM) |
Disconnect the fuel temperature sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
F11-2 or E26-4 (THF) - Body ground
Always
10 kΩ or higher
Reconnect the fuel temperature sensor connector.
Reconnect the ECM connector.
|
|
||||
| OK | |
| 9. REPLACE ECM |
Replace the ECM (Click here).
|
|
||||
| 10. BLEED AIR FROM FUEL SYSTEM |
Bleed the air from the fuel system (Click here).
| NEXT | |
| 11. PERFORM FUEL SUPPLY PUMP INITIALIZATION |
Perform fuel supply pump initialization (Click here).
|
|
||||
| 12. REPAIR OR REPLACE HARNESS OR CONNECTOR |
Repair or replace the harness or connector.
| NEXT | |
| 13. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the intelligent tester to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch to ON for 1 second or more.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Confirm that the DTC is not output again.
| NEXT | ||
| ||
