P0717 Input Speed Sensor Circuit No Signal
Diagnostic trouble codes · Vehicles built from Jun 2011
DESCRIPTION
This sensor detects the rotation speed of the turbine, which shows the input revolution of the transmission. By comparing the input speed signal (NT) with the counter gear speed sensor signal (SP2), the ECM detects the shift timing of the gears and controls the engine torque and hydraulic pressure according to various conditions. As a result, smooth gear shift is achieved.

| DTC Code |
DTC Detection Condition |
Trouble Area |
| P0717 |
All conditions below are detected for 5 sec. or more continuously (1 trip detection logic): (a) Gear changes not performed (b) Gear position: 4th or 5th (c) Transmission input shaft rpm: less than 300 rpm (d) Transmission output shaft rpm: 1,000 rpm or more (e) Park/Neutral position switch
|
|
MONITOR DESCRIPTION
This DTC indicates that a pulse is not output from the speed sensor NT (input speed sensor) or is output only a little. The NT terminal of the ECM detects the pulse signal from the speed sensor (NT) (input RPM). The ECM outputs a gear shift signal comparing the input speed sensor (NT) with the output speed sensor (SP2).While the vehicle is operating in the 4th or 5th gear position with the shift lever on D, if the input shaft revolution is less than 300 rpm*1 although the output shaft revolution is 1,000 rpm or more*2, the ECM detects the trouble, illuminates the MIL and stores the DTC.
- HINT:
- *1: Pulse is not output or is irregularly output.
- *2: The vehicle speed is approximately 50 km/h (31 mph) or more.
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- Using the intelligent tester's Data List allows switch, sensor, actuator and other item values to be read without removing any parts. Reading the Data List early in troubleshooting is one way to save time.
- Warm up the engine.
- Turn the ignition switch OFF.
- Connect the intelligent tester to the DLC3.
- Turn the ignition switch ON and push the tester main switch ON.
- Enter the following menus: Powertrain / Engine and ECT / Data List.
- Follow the instructions on the tester and read the Data List.
| Tester Display |
Measurement Item/Range |
Normal Condition |
Diagnostic Note |
| SPD (NT) |
Input turbine speed/ display: 50 r/min |
|
- |
- CAUTION:
- In the table above, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
- HINT:
- SPD (NT) is always 0 while driving:
Open or short in the sensor or circuit.
- SPD (NT) is always more than 0 and less than 300 rpm while driving the vehicle at 50 km/h (31 mph) or more:
Sensor trouble, improper installation, or intermittent connection trouble of the circuit.
- SPD (NT) is always 0 while driving:
| 1. INSPECT SPEED SENSOR (INSTALLATION) |
Check the speed sensor NT installation.

- OK:
- Installation bolt is tightened properly and there is no clearance between the sensor and transmission case.
|
|
||||
| OK | |
| 2. INSPECT INPUT SPEED SENSOR (NT) |
![]() ![]() |
Disconnect the T6 sensor connector from the transmission.
Measure the resistance of the sensor.
- Standard resistance:
Tester Connection
Condition
Specified Condition
1 - 2
20°C (68°F)
560 to 680 Ω
- HINT:
-


- Reference: Inspect using an oscilloscope.
- Check the waveform of the ECM connector.
- OK:
- Refer to illustration
Item
Content
Tester Connection
E16-35 (NT+) - E16-27 (NT-)
Tool Setting
1 V/DIV., 2 msec./DIV.
Condition
Engine is idling (P or N position)
|
|
||||
| OK | |
| 3. CHECK WIRE HARNESS (INPUT SPEED SENSOR - ECM) |
Disconnect the E16 ECM connector.

Measure the resistance of the wire harness side connector.
- Standard resistance:
Tester Connection
Condition
Specified Condition
E16-35 (NT+) - E16-27 (NT-)
20°C (68°F)
560 to 680 Ω
E16-35 (NT+) - Body ground
20°C (68°F)
10 kΩ or higher
E16-27 (NT-) - Body ground
20°C (68°F)
10 kΩ or higher
|
|
||||
| OK | ||
| ||

