SERVICE DATA
Specifications · Vehicles built from Jun 2011
| for 2.2 kW Type bosch made |
Starter |
No-load characteristics current |
123A or less at 11.5 V |
| Starter armature assembly |
Maximum circle runout |
0.04 mm (0.0016 in.) |
|
| Standard circle runout |
0.02 mm (0.0008 in.) |
||
| Standard commutator diameter |
32.2 mm (1.2783 in.) |
||
| Minimum commutator diameter |
31.1 mm (1.2347 in.) |
||
| Standard undercut depth |
0.9 mm (0.0354 in.) |
||
| Minimum undercut depth |
0.4 mm (0.0157 in.) |
||
| Segments |
Below 1.7 Ω |
||
| Segment - Coil core |
10 kΩ or higher |
||
| Brush |
Standard length |
14.0 mm (0.5558 in.) |
|
| Minimum length |
9.0 mm (0.3543 in. ) |
||
| Tester connection A-B |
10 kΩ or higher |
||
| Tester connection A-C |
10 kΩ or higher |
||
| Tester connection A-D |
Below 1 Ω |
||
| Tester connection B-C |
Below 1 Ω |
||
| Tester connection B-D |
10 kΩ or higher |
||
| Tester connection C-D |
10 kΩ or higher |
||
| Magnet starter switch |
Terminal 50 - Terminal C |
Below 1 Ω |
|
| Terminal 50 - Body |
Below 2 Ω |
||
| for 2.2 kW Type denso made |
Starter |
No-load characteristics current |
120 A or less at 11.5 V |
| Starter armature |
Maximum circle runout |
0.05 mm (0.0020 in.) |
|
| Standard commutator diameter |
35.5 mm (1.378 in.) |
||
| Minimum commutator diameter |
34.0 mm (1.339 in.) |
||
| Standard undercut depth |
0.7 mm (0.028 in.) |
||
| Minimum undercut depth |
0.2 mm (0.008 in.) |
||
| Segments |
Below 1 Ω |
||
| Segment - Coil core |
10 kΩ or higher |
||
| Brush length |
Standard length |
16.5 mm (0.650 in.) |
|
| Minimum length |
9.0 mm (0.354 in. ) |
||
| Brush spring |
Standard spring installed load |
26.5 to 32.3 N (2.7 to 3.3 kgf*cm, 5.9 to 7.3 in.*lbf) |
|
| Minimum spring installed load |
17.6 N (1.8 kgf*cm, 4.0 in.*lbf) |
||
| Brush holder |
Positive brush - Negative brush |
10 kΩ or higher |
|
| Magnet starter switch |
Terminal 50 - Terminal C |
Below 1 Ω |
|
| Terminal 50 - Body |
Below 2 Ω |
||
| for 2.7 kW Type |
Starter |
No-load characteristics current |
180 A or less at 11 V |
| Starter armature assembly |
Maximum circle runout |
0.05 mm (0.0020 in.) |
|
| Standard commutator diameter |
36.0 mm (1.417 in.) |
||
| Minimum commutator diameter |
35.0 mm (1.378 in.) |
||
| Standard undercut depth |
0.7 mm (0.028 in.) |
||
| Minimum undercut depth |
0.2 mm (0.008 in.) |
||
| Segments |
Below 1 Ω |
||
| Segment - Coil core |
10 kΩ or higher |
||
| Brush length |
Standard length |
20.5 mm (0.814 in.) |
|
| Minimum length |
11.0 mm (0.433 in.) |
||
| Brush spring |
Standard spring installed load |
34.3 to 42.1N (3.5 to 4.3 kgf*cm, 7.7 to 9.5 in.*lbf) |
|
| Minimum spring installed load |
18.6 N (1.9 kgf*cm, 4.2 in.*lbf) |
||
| Starter yoke |
Lead wire - Field coil brush lead |
Below 1 Ω |
|
| Lead wire - Starter yoke body |
10 kΩ or higher |
||
| Brush holder |
Positive brush - Negative brush |
10 kΩ or higher |
|
| Magnet starter switch |
Terminal 50 - Terminal C |
Below 1 Ω |
|
| Terminal 50 - Body |
Below 2 Ω |
||
| Glow plug |
Resistance |
Approx. 0.95 Ω |
|
| Glow plug (for DPF) |
Approx. 1.0 Ω |
||
| ECT sensor |
Resistance |
Approx. 20°C (68°F) 2.32 to 2.59 kΩ |
|
| Approx. 80°C (176°F) 0.310 to 0.326 kΩ | |||
| Starter relay |
Specified resistance 3-5 |
10 kΩ or higher |
|
| Below 1 Ω (when battery voltage is applied to terminal 1 and 2) | |||
| Glow relay |
Specified resistance 3-5 |
10 kΩ or higher |
|
| Below 1 Ω (when battery voltage is applied to terminal 1 and 2) | |||
| Ignition switch |
Tester connection - |
Switch condition Lock |
Specified condition 10 kΩ or higher |
| Tester connection 2 (ACC) - 4 (AM1) |
Switch condition ACC |
Specified condition Below 1 Ω |
|
| Tester connection 1 (IG1) - 4 (AM1) 2 (ACC) - 4 (AM1) 5 (AM2) - 6 (IG2) |
Switch condition ON |
Specified condition Below 1 Ω |
|
| Tester connection 1 (IG1) - 4 (AM1) 3 (ST1) - 4 (AM1) 5 (AM2) - 6 (IG2) 5 (AM2) - 7 (ST2) |
Switch condition START |
Specified condition Below 1 Ω |
|