SERVICE DATA
Specifications · Vehicles built from Jun 2011
| for 2.0 kW Type |
Starter |
No-load characteristics current |
100 A or less at 11.5 V |
| Starter armature assembly |
Maximum circle runout |
0.05 mm (0.0020 in.) |
|
| Standard commutator diameter |
35.0 mm (1.378 in.) |
||
| Minimum commutator diameter |
34.0 mm (1.339 in.) |
||
| Standard undercut depth |
0.7 mm (0.028 in.) |
||
| Minimum undercut depth |
0.2 mm (0.008 in.) |
||
| Segments |
Below 1 Ω |
||
| Segment - Coil core |
10 kΩ or higher |
||
| Brush length |
Standard length |
15.0 mm (0.591 in.) |
|
| Minimum length |
9.0 mm (0.354 in.) |
||
| Brush spring |
Standard spring installed load |
21.5 to 27.5N (2.2 to 2.8 kgf*cm, 4.8 to 6.2 in.*lbf) |
|
| Minimum spring installed load |
12.7 N (1.3 kgf*cm, 2.9 in.*lbf) |
||
| Starter yoke |
Lead wire - Field coil brush lead |
Below 1 Ω |
|
| Shunt coil terminals |
1.5 to 1.9 Ω at 20°C(68°F) |
||
| Brush holder |
Positive brush - Negative brush |
10 kΩ or higher |
|
| Magnet starter switch |
Terminal 50 - Terminal C |
Below 1 Ω |
|
| Terminal 50 - Body |
Below 2 Ω |
||
| for 2.2 kW Type |
Starter |
No-load characteristics current |
123 A or less at 11.5 V |
| Starter armature |
Maximum circle runout |
0.04 mm (0.0016 in.) |
|
| Standard circle runout |
0.02 mm (0.0008 in.) |
||
| Standard commutator diameter |
32.2 mm (1.2783 in.) |
||
| Minimum commutator diameter |
31.1 mm (1.2347 in.) |
||
| Standard undercut depth |
0.9 mm (0.03543 in.) |
||
| Minimum undercut depth |
0.4 mm (0.0157 in.) |
||
| Segments |
Below 1.7 Ω |
||
| Segment - Coil core |
10 kΩ or higher |
||
| Brush |
Standard length |
14.0 mm (0.5558 in.) |
|
| Minimum length |
9.0 mm (0.354 in. ) |
||
| Tester connection A-B |
10 kΩ or higher |
||
| Tester connection A-C |
10 kΩ or higher |
||
| Tester connection A-D |
Below 1 Ω |
||
| Tester connection B-C |
Below 1 Ω |
||
| Tester connection B-D |
10 kΩ or higher |
||
| Tester connection C-D |
10 kΩ or higher |
||
| Magnet starter switch |
Terminal 50 - Terminal C |
Below 1 Ω |
|
| Terminal 50 - Body |
Below 2 Ω |
||
| for 2.7 kW Type |
Starter |
No-load characteristics current |
180 A or less at 11 V |
| Starter armature assembly |
Maximum circle runout |
0.05 mm (0.0020 in.) |
|
| Standard commutator diameter |
36.0 mm (1.417 in.) |
||
| Minimum commutator diameter |
35.0 mm (1.378 in.) |
||
| Standard undercut depth |
0.7 mm (0.028 in.) |
||
| Minimum undercut depth |
0.2 mm (0.008 in.) |
||
| Segments |
Below 1 Ω |
||
| Segment - Coil core |
10 kΩ or higher |
||
| Brush length |
Standard length |
20.5 mm (0.814 in.) |
|
| Minimum length |
11.0 mm (0.433 in.) |
||
| Brush spring |
Standard spring installed load |
26 to 45N (3 to 5 kgf*cm, 5.8 to 10.1 in.*lbf) |
|
| Minimum spring installed load |
12 N (1 kgf*cm, 2.8 in.*lbf) |
||
| Starter yoke |
Lead wire - Field coil brush lead |
Below 1 Ω |
|
| Lead wire - Starter yoke body |
10 kΩ or higher |
||
| Brush holder |
Positive brush - Negative brush |
10 kΩ or higher |
|
| Magnet starter switch |
Terminal 50 - Terminal C |
Below 1 Ω |
|
| Terminal 50 - Body |
Below 2 Ω |
||
| Glow plug |
Resistance |
Approx. 0.95 Ω |
|
| Glow plug (for DPF) |
Approx. 1.0 Ω |
||
| ECT sensor |
Resistance |
Approx. 20°C(68°F) 2.32 to 2.59 kΩ |
|
| Approx. 80°C(176°F) 0.310 to 0.326 kΩ | |||
| Starter relay |
Specified resistance 3-5 |
10 kΩ or higher |
|
| Below 1 Ω (when battery voltage is applied to terminal 1 and 2) | |||
| Glow relay |
Specified resistance 3-5 |
10 kΩ or higher |
|
| Below 1 Ω (when battery voltage is applied to terminal 1 and 2) | |||