TORQUE SPECIFICATIONS
Specifications · Vehicles built from Aug 2014
Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2014 from Aug 2014
| Part tightened |
N*m |
kgf*cm |
ft.*lbf |
| Camshaft x Camshaft timing gear |
78 |
795 |
58 |
| Camshaft bearing cap x Cylinder head : for bolt A |
12 |
122 |
9 |
| Camshaft bearing cap x Cylinder head : for except bolt A |
15.5 |
158 |
11 |
| Timing gear case plug x Timing chain cover |
16.6 |
169 |
12 |
| Timing chain guide x Cylinder head |
10 |
102 |
7 |
| Cylinder head cover x Cylinder head |
9.0 |
92 |
80 in.*lbf |
| Ignition coil x Cylinder head cover |
9.0 |
92 |
80 in.*lbf |
| Engine mounting bracket LH x Cylinder block |
51 |
520 |
38 |
| Engine mounting bracket RH x Cylinder block |
51 |
520 |
38 |
| Camshaft timing oil control valve x Cylinder head |
8.0 |
82 |
71 in.*lbf |
| Camshaft position sensor x Cylinder head |
8.5 |
87 |
75 in.*lbf |
| No. 1 water by-pass pipe x Timing chain cover |
17.5 |
178 |
13 |
| No. 1 idler pulley x Timing chain cover |
43 |
439 |
32 |
| V-ribbed belt tensioner x Timing chain cover : for bolt 1 |
40 |
408 |
30 |
| V-ribbed belt tensioner x Timing chain cover : for bolt 2 |
21 |
214 |
15 |
| V-ribbed belt tensioner x Timing chain cover : for bolt 3 |
43 |
438 |
32 |
| No. 1 compressor mounting bracket x Cylinder block : for bolt A and B |
45 |
459 |
33 |
| No. 1 compressor mounting bracket x Cylinder block : for bolt C |
24.5 |
250 |
18 |
| Idler pulley assembly x No. 1 compressor mounting bracket |
44 |
449 |
32 |
| Exhaust manifold x Cylinder head |
36 |
367 |
27 |
| Air switching valve x Cylinder head |
20 |
204 |
15 |
| Intake pipe insulator x Air switching valve |
20 |
204 |
15 |
| Intake pipe insulator x Exhaust manifold |
20 |
204 |
15 |
| Exhaust heat insulator x Exhaust manifold |
12 |
122 |
9 |
| Intake manifold x Cylinder head |
25 |
255 |
18 |
| Ground wire x Cylinder block |
31 |
316 |
23 |
| Ventilation pipe x Cylinder head cover |
18 |
184 |
13 |
| Engine mounting bracket x Body |
38 |
388 |
28 |
| Rear end plate x Cylinder block |
18 |
184 |
13 |
| for Manual Transmission: Flywheel x Crankshaft : Precoated part |
1st: 26.5 2nd: Turn 90° |
1st: 270 2nd: Turn 90° |
1st: 20 2nd: Turn 90° |
| for Automatic Transmission: Drive plate x Crankshaft : Precoated part |
74 |
755 |
55 |
| Cooler compressor x No. 1 compressor mounting bracket |
25 |
250 |
18 |
| Suction hose x Timing chain cover |
5.0 |
51 |
44in.*lbf |
| Oil dipstick guide x Cylinder head |
8.0 |
82 |
71 in.*lbf |
| Vane pump x Timing chain cover |
21 |
214 |
15 |
| Engine wire x Junction block |
13 |
133 |
10 |
| Ground wire x Cylinder block |
31 |
316 |
23 |
| Ground wire x Body |
13 |
133 |
10 |
| A/F sensor bracket x Body |
13 |
133 |
10 |
| Air cleaner x Body |
14 |
143 |
10 |
| Intake air connector x Cylinder head cover |
8.0 |
82 |
71 in.*lbf |
| Intake air connector x Hose clamp |
5.0 |
51 |
44 in.*lbf |
| No. 1 engine under cover x Body |
28 |
286 |
21 |
| Stud bolt x Cylinder block |
7.5 |
77 |
66 in.*lbf |
| No. 2 balance shaft drive gear x Balance shaft |
36 |
367 |
27 |
| No. 2 balance shaft thrust washer x Cylinder block |
18 |
184 |
13 |
| No. 1 balance shaft drive gear x Balance shaft |
36 |
367 |
27 |
| No. 1 balance shaft thrust washer x Cylinder block |
18 |
184 |
13 |
| Oil nozzle x Cylinder block |
7.0 |
71 |
62 in.*lbf |
| Water drain cook x Cylinder block |
19.6 |
200 |
15 |
| Water drain cook plug x Water drain cook |
13 |
130 |
9 |
| Crankshaft bearing cap x Cylinder block |
1st: 39 2nd: Turn 90° |
1st: 398 2nd: Turn 90° |
1st: 29 2nd: Turn 90° |
| Connecting rod cap x Connecting rod cap |
1st: 24.5 2nd: Turn 90° |
1st: 250 2nd: Turn 90° |
1st: 18 2nd: Turn 90° |
| No. 1 head straight screw plug x Cylinder head |
44 |
449 |
32 |
| No. 2 head straight screw plug x Cylinder head |
140 |
1428 |
103 |
| Stud bolt x Cylinder head : for A |
3.0 |
31 |
27 in.*lbf |
| Stud bolt x Cylinder head : for B and C |
7.5 |
76 |
66 in.*lbf |
| Oil control valve filter plug x Cylinder head |
30 |
306 |
22 |
| No. 4 chain vibration damper x Cylinder block |
18 |
184 |
13 |
| Balance shaft drive gear shaft x Cylinder block |
25 |
255 |
18 |
| No. 2 chain tensioner x Cylinder block |
18 |
184 |
13 |
| No. 3 chain vibration damper x Cylinder block |
18 |
184 |
13 |
| No. 2 chain vibration damper x Cylinder block |
27 |
270 |
20 |
| Rear oil seal retainer x Cylinder block |
13 |
133 |
10 |
| Oil filter bracket x Cylinder block : for union bolt |
24.5 |
250 |
18 |
| Oil filter bracket x Cylinder block : for nut |
25 |
255 |
18 |
| Oil filter union x Cylinder block |
43 |
438 |
32 |
| Oil filter x Oil filter bracket |
17.2 |
175 |
13 |
| Cylinder block x Cylinder head |
1st: 39 2nd: Turn 90° 3nd: Turn 90° |
1st: 398 2nd: Turn 90° 3nd: Turn 90° |
1st: 29 2nd: Turn 90° 3nd: Turn 90° |
| Camshaft timing sprocket x Camshaft |
78 |
795 |
58 |
| Chain vibration damper x Cylinder block |
21 |
214 |
15 |
| Chain tensioner slipper x Cylinder block |
21 |
214 |
15 |
| Chain tensioner x Cylinder block |
10 |
102 |
7 |
| Stud bolt x No. 1 oil pan |
3.0 |
31 |
27 in.*lbf |
| No. 1 oil pan x Cylinder block |
26 |
265 |
19 |
| Crankshaft x Crankshaft pulley |
260 |
2,651 |
192 |
| Ventilation valve x Cylinder head cover |
5.0 |
51 |
44 in.*lbf |
| Tensioner pulley x Belt tensioner |
50 |
510 |
37 |