2014 Hilux · Service Manual ENGINE

P0200 Injector Circuit / Open

Diagnostic trouble codes · Vehicles built from Aug 2014

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

HINT:
  1. For more information on the injector driver (EDU) (Click here).
  2. If DTC P0200 is present, refer to the "Diagnostic Trouble Code (DTC) Table for Common Rail System" (Click here).

The EDU drives the injectors at high speed. The EDU has realized high-speed driving under high-pressure fuel conditions using the DC/DC converter, which provides a high voltage and the quick-charging system. Soon after the EDU receives an injection command (IJT) signal from the ECM, the EDU responds to the command with an injector injection confirmation (IJF) signal when the current is applied to the injector.
A221606E01
DTC No.
DTC Detection Condition
Trouble Area
P0200
  1. Open or short in injector driver (EDU) or injector circuit
After engine is started, there is no IJF signal from EDU to ECM, despite ECM sending IJT signals to EDU
(1 trip detection logic)
  1. Open or short in injector driver (EDU) circuit
  2. Injector
  3. EDU
  4. ECM

MONITOR DESCRIPTION

  1. P0200 (Open or short in injector driver (EDU) or injector circuit):
    The ECM continuously monitors both injection command (IJT) signals and injection confirmation (IJF) signal. This DTC will be set if the ECM judges that the number of IJT signals and IJF signals are inconsistent.
    The injectors are grounded over a Field Effect Transistor (FET) and a serial resistor. This resistor creates a voltage drop, which is monitored by the EDU, in relation to the current drawn by the injector. When the injector current becomes too high, the voltage drop over the resistor becomes higher than a specified level and for that injector no IJF signal is sent to the ECM.
    P0200 refers to a malfunction of injector drive circuit or injector circuit.
    If this DTC is set, the ECM enters the fail-safe mode and limits engine power. The fail-safe mode continues until the ignition switch is turned OFF.
    A145849E02
  1. PULSE GENERATION INSPECTION

    HINT:
    The problem area can be identified by checking the waveform at the following terminals.

    A221611E01

    HINT:
    A and D are on the ECM side, and B and C are on the EDU side.
    Malfunction Point
    Trouble Area
    A
    1. ECM
    B (If A is normal)
    1. Open or short in "#1 to #4 (ECM)" - "#10 to #40 (EDU)" harness or connector
    C (If A and B are normal)
    1. Open or short in "IJ1+ to IJ4+ (EDU)" - "IJ1- to IJ4- (EDU)" circuit
    2. Injector
    3. EDU
    D (If A, B and C are normal)
    1. Open or short in "INJF (EDU)" - "INJF (ECM)" circuit (P1271 is set simultaneously)

    1. A145851E01
      Reference: Inspection using the oscilloscope.
      During idling, the correct waveform is as shown in the diagram.
      Inspection Point
      Specified Condition
      A and B
      Correct waveform is as shown

    2. A155125E01
      Reference: Inspection using the oscilloscope.
      During idling, the correct waveform is as shown in the diagram.
      Inspection Point
      Specified Condition
      C and D
      Correct waveform is as shown


MONITOR STRATEGY

Required sensor
INJF signal from EDU
Frequency of operation
Continuous
Duration
10 seconds
MIL operation
1 driving cycle

TYPICAL ENABLING CONDITIONS

Item
Specification
Minimum
Maximum
Engine speed
500 rpm
-
Battery voltage
11 V
-
Ignition switch
ON
ON

TYPICAL MALFUNCTION THRESHOLDS

Threshold
Injection missing counter* for all cylinders, or for one individual cylinder, reaches specified number (taking approximately 1 second from starting engine)
*: Increases when no IJF signal is received from the EDU despite the ECM sending the IJT signals.

WIRING DIAGRAM

A205139E06
A159235E02

INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
  1. If P0200 and P1271 are present simultaneously, there is an open in the INJF wire harness between the EDU and ECM, or there is an open in the wire harness for both the injectors and pressure discharge valve.
  2. Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. INSPECT INJECTOR ASSEMBLY

  1. A191333E04
    Disconnect the F5, F6, F7 and F8 injector connectors.

  1. Measure the resistance of the injection assembly.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    0.42 to 0.52 Ω



NG
REPLACE INJECTOR ASSEMBLY (Click here)
OK


2. CHECK HARNESS AND CONNECTOR (INJECTOR DRIVER [EDU] - INJECTOR ASSEMBLY)

  1. Check the harness and connector between the injector and EDU (INJF terminal).

    1. A221612E01
      Disconnect the F5, F6, F7 and F8 injector connectors.

    2. Disconnect the I17 and I18 EDU connectors.

    3. Measure the resistance of the wire harness side connector.

      Standard resistance (Check for open):
      Tester Connection
      Specified Condition
      F5-1 - IJ1+ (I17-1)
      Below 1 Ω
      F6-1 - IJ2+ (I17-6)
      F7-1 - IJ3+ (I17-5)
      F8-1 - IJ4+ (I18-3)
      F5-2 - IJ1- (I18-6)
      F6-2 - IJ2- (I18-4)
      F7-2 - IJ3- (I18-2)
      F8-2 - IJ4- (I18-5)

      Standard resistance (Check for short):
      Tester Connection
      Specified Condition
      F5-1 or IJ1+ (I17-1) - Body ground
      10 kΩ or higher
      F6-1 or IJ2+ (I17-6) - Body ground
      F7-1 or IJ3+ (I17-5) - Body ground
      F8-1 or IJ4+ (I18-3) - Body ground
      F5-2 or IJ1- (I18-6) - Body ground
      F6-2 or IJ2- (I18-4) - Body ground
      F7-2 or IJ3- (I18-2) - Body ground
      F8-2 or IJ4- (I18-5) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK HARNESS AND CONNECTOR (INJECTOR DRIVER [EDU] - ECM)

  1. A221613E01
    Disconnect the I19 EDU connector.

  1. Disconnect the E8 ECM connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    #10 (I19-4) - #1 (E8-24)
    Below 1 Ω
    #20 (I19-8) - #2 (E8-23)
    #30 (I19-7) - #3 (E8-22)
    #40 (I19-3) - #4 (E8-21)
    INJF (I19-5) - INJF (E8-25)

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    #10 (I19-4) or #1 (E8-24) - Body ground
    10 kΩ or higher
    #20 (I19-8) or #2 (E8-23) - Body ground
    #30 (I19-7) or #3 (E8-22) - Body ground
    #40 (I19-3) or #4 (E8-21) - Body ground
    INJF (I19-5) or INJF (E8-25) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. INSPECT INJECTOR DRIVER (EDU) (BATTERY VOLTAGE)

  1. A221614E01
    Disconnect the I17 EDU connector.

  1. Turn the ignition switch ON.

  1. Measure the voltage of the EDU connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    +B (I17-2) - GND (I17-3)
    11 to 14 V



NG
CHECK INJECTOR DRIVER POWER SOURCE CIRCUIT (BATTERY - EDU)
OK


5. REPLACE INJECTOR DRIVER (EDU)
  1. Replace injector driver (Click here).


NEXT


6. CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON.

  1. Turn the tester ON.

  1. Clear DTCs (Click here).

  1. Start the engine.

  1. Allow the engine to idle for 30 seconds or more.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    No output
    A
    P0200
    B

    HINT:
    If the engine does not stat, replace the ECM.



B
REPLACE ECM (Click here)
A

END


← P0200 Injector Circuit / Open (Aug 2013 – Jul 2014)P0335 Crankshaft Position Sensor "A" Circuit Malfunction (+ P0339) (Jun 2011 – Jul 2012) →