2014 Hilux · Service Manual ENGINE

P0405 Exhaust Gas Recirculation Sensor "A" Circuit Low

Diagnostic trouble codes · Vehicles built from Aug 2014

Also covers:

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The EGR valve position sensor is mounted on the EGR valve and used for detecting the lift amount of the valve. The lift amount detected by the sensor is provided to the ECM as feedback, and then the ECM regulates the lift amount of the valve in accordance with the engine running condition.
DTC No.
DTC Detection Condition
Trouble Area
P0405
EGR valve position sensor output voltage is less than 0.1 V for more than 5 seconds
(1 trip detection logic)
  1. Open or short in EGR valve position sensor circuit
  2. EGR valve position sensor
  3. ECM
P0406
EGR valve position sensor output voltage is more than 4.9 V for more than 5 seconds
(1 trip detection logic)
  1. Open or short in EGR valve position sensor circuit
  2. EGR valve position sensor
  3. ECM

HINT:
After confirming DTCs P0405 and P0406, check the EGR valve opening angle condition by entering the following menus on the intelligent tester: Powertrain / Engine / Data List / EGR Position.
Result
Condition
Changes between 0.3 to 4.2 V
Normal
Less than 0.1 V
P0405 (Low input voltage)
More than 4.9 V
P0406 (High input voltage)

HINT:
The result values above are for when the ignition switch is ON (engine is stopped), or when the engine is fully warmed-up and idling.


MONITOR DESCRIPTION

When the output voltage of the EGR valve position sensor deviates from the normal operating range of 0.1 to 4.9 V for more than 0.5 seconds, the ECM interprets this as a malfunction of the sensor circuit, and illuminates the MIL.
G039134E07

WIRING DIAGRAM

A154732E01

INSPECTION PROCEDURE

NOTICE:
If the ECM is replaced, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. CHECK ECM (VC VOLTAGE)
A085350E06
  1. Disconnect the E2 EGR valve position sensor connector.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    E2-1 (VC) - E2-2 (E2)
    4.5 to 5.5 V

  1. Reconnect the EGR valve position sensor connector.



NG
Go to step 3
OK


2. INSPECT EGR VALVE POSITION SENSOR (RESISTANCE)
  1. Inspect the EGR valve position sensor (Click here).



NG
REPLACE EGR VALVE POSITION SENSOR
OK


3. CHECK HARNESS AND CONNECTOR (EGR VALVE POSITION SENSOR - ECM)
G034912E07
  1. Disconnect the E2 sensor connector.

  1. Disconnect the E7 and E8 ECM connectors.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    E2-1 (VC) - E8-18 (VC)
    Below 1 Ω
    E2-3 (EGLS) - E7-33 (EGLS)
    Below 1 Ω
    E2-2 (E2) - E8-28 (E2)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    E2-1 (VC) or E8-18 (VC) - Body ground
    10 kΩ or higher
    E2-3 (EGLS) or E7-33 (EGLS) - Body ground
    10 kΩ or higher
    E2-2 (E2) or E8-28 (E2) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM


← P0405 Exhaust Gas Recirculation Sensor "A" Circuit Low (+ P0406) (Aug 2013 – Jul 2014)P0488 Exhaust Gas Recirculation Throttle Position Control Range / Performance (Jun 2011 – Jul 2012) →