2014 Hilux · Service Manual ENGINE

REASSEMBLY

Removal / installation · Vehicles built from Jun 2011

HINT:
Use high-temperature grease to lubricate the bearing and sliding parts when assembling the starter.


1. INSTALL STARTER CENTER BEARING CLUTCH SUB-ASSEMBLY

  1. A196356E01
    Apply high-temperature grease to the starter drive lever set pin as shown in the illustration.

  1. A084665E01
    Install the drive lever set pin to the starter center bearing clutch sub-assembly.

  1. Install the starter center bearing clutch and drive lever set pin together to the starter drive housing.


2. INSTALL PLANET GEAR

A197984E01
  1. Apply high-temperature grease to the planet gears and pin parts of the planet shaft.

  1. Install the 3 planetary gears onto the pins of the planet shaft.


3. INSTALL STARTER ARMATURE ASSEMBLY

NOTICE:
Do not drop the starter armature assembly.

  1. A196357E01
    Apply high-temperature grease to the plate washer, a new snap ring and the bearing as shown in the illustration.

  1. Hold the starter commutator end frame between aluminum plates in a vise.

    NOTICE:
    Do not damage the starter commutator end frame.

  1. A196360E01
    Apply high-temperature grease to the starter armature assembly as shown in the illustration.

  1. Install the starter armature assembly to the starter commutator end frame assembly.

  1. Install the plate washer to the starter armature shaft.

  1. A073993
    Using snap ring pliers, install the snap ring.

    NOTICE:
    1. Be sure to install the snap ring in the armature shaft groove securely.
    2. Be sure to properly install the snap ring because it easily expands.

  1. Check the snap ring length.

    1. A058810E03
      Using a vernier caliper, measure the snap ring length.

      Maximum length:
      5.0 mm (0.197 in.)

      If the length is greater than the maximum, replace the snap ring.


4. INSTALL STARTER COMMUTATOR END FRAME COVER

  1. A084616
    Install the starter commutator end frame cover to the starter commutator end frame.


5. INSTALL STARTER ARMATURE PLATE

A073991E20
  1. Align the claws of the armature plate with the protrusion inside the starter yoke, and install the starter armature plate.


6. INSTALL STARTER COMMUTATOR END FRAME ASSEMBLY

  1. A079727E09
    Align the rubber part on the starter commutator end frame with the cutout of the starter yoke.

  1. Install the starter commutator end frame to the starter yoke.

    NOTICE:
    The magnet of the starter yoke may attract the starter armature when the starter commutator end frame is installed, causing the magnet to break.


7. INSTALL STARTER YOKE ASSEMBLY

  1. A196821E01
    Align the claw of the starter yoke with the groove inside the starter drive housing.

  1. A082689
    Install the starter yoke with the 2 through bolts.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }


8. INSTALL REPAIR SERVICE STARTER KIT

  1. A196358E01
    Apply high-temperature grease to the plunger and hook.

  1. Hang the plunger hook of the repair service starter kit on the drive lever set pin.

  1. A082694
    Install the plunger and return spring.

  1. A076124
    Install the repair service starter kit with the 2 screws.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. A081590
    Connect the lead wire to terminal C with the nut.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

← INSPECTION (from Jun 2011)INSTALLATION (Jun 2011 – Jul 2012) →