2014 Hilux · Service Manual ENGINE

REASSEMBLY

Removal / installation · Vehicles built from Aug 2013

Versions by build date: Jun 2011 – Jul 2013 from Aug 2013


1. INSTALL OIL COOLER ASSEMBLY

  1. A099962E01
    Install 2 new O-rings to the oil cooler.

  1. Install the oil cooler and 2 plate washers to the tank with the 2 nuts.

    Torque:
    8.3 N*m{ 85 kgf*cm , 74 in.*lbf }

  1. Install the 2 cooler pipes.

    Torque:
    15 N*m{ 150 kgf*cm , 11 ft.*lbf }

    HINT:
    Set the cooler pipe labeled A to the location and angle shown in the illustration.


2. INSPECT LOCK PLATE FOR DAMAGE

  1. A099690E01
    Inspect lock plate for damage.
    If the sides of the lock plate groove are deformed, reassembly of the tank will be impossible. Correct any deformations with pliers.
    Coolant will leak if the bottom of the lock plate groove is damaged or dented. Repair or replace it if necessary. Core

    NOTICE:
    The radiator can only be recaulked twice. After the second time, the radiator core must be replaced.


3. INSTALL RADIATOR TANK UPPER AND RADIATOR TANK LOWER

  1. A113341E01
    Check that there are no foreign objects in the lock plate groove, and install a new O-ring. Make sure the O-ring is not twisted.

    HINT:
    When cleaning the lock plate groove, lightly rub it with sandpaper without scratching it.

  1. Install the tank without damaging the O-ring.

  1. A113342E01
    Tap the lock plate with a plastic-faced hammer so that there is no gap between the lock plate and the tank.


4. ASSEMBLE SST

  1. A234961E02
    Install the punch assembly to part A of the overhaul handle as shown in the illustration.
    SST
    09230-01010   (09231-01010, 09231-01020)
    09231-14010  

  1. While gripping the handle, adjust the stopper bolt so that dimension B is as specified below.

    Dimension B:
    8.4 mm (0.331 in.)


5. CAULK LOCK PLATE

  1. A099703E01
    Lightly press SST against the lock plate in the order shown in the illustration. Repeat this step a few times, and then fully caulk the lock plate by squeezing the handle until stopped by the stopper bolt.
    SST
    09230-01010   (09231-01010, 09231-01020)
    09231-14010  

    NOTICE:
    A099704E01
    1. Do not press the protruding areas around the ports (1) and bracket (2).

    2. A099705E03
      Do not use SST to press the areas indicated by the circle marks in the illustration. Use pliers and be careful not to damage the core plates.

  1. A099706E01
    Check the lock plate height, H, after completing the caulking.

    Standard plate height H:
    8.8 mm (0.346 in.)

    If the height is not as specified, readjust the stopper bolt of the handle and caulk the lock plate again.


6. INSTALL RADIATOR DRAIN COCK PLUG
  1. Install a new O-ring to the drain cock plug.

  1. Install the drain cock plug.


7. CHECK FOR WATER LEAKS

  1. A099707E01
    Plug the inlet and outlet pipes of the radiator with SST.
    SST
    09230-01010   (09231-00030, 09231-00060)

  1. Using a radiator cap tester, apply pressure to the radiator.

    Standard test pressure:
    177 kPa (1.8 kgf/cm2, 26 psi)

  1. Submerge the radiator in water.

  1. A090282E01
    Inspect for leaks.

    HINT:
    For radiators with resin tanks, there is clearance between the tank and lock plate where a small amount of air will remain. This air is released when the radiator is submerged in water, giving the appearance of an air leak. Before performing the water leak test, first shake the radiator in the water until all air bubbles are released.


8. INSTALL RADIATOR BRACKET SUB-ASSEMBLY

  1. A099961E01
    Install the 2 brackets with the 4 bolts.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }

← REASSEMBLY (Jun 2011 – Jul 2013)INSTALLATION (Jun 2011 – Jul 2012) →