2014 Hilux · Service Manual BRAKE

TERMINALS OF ECU

System information · Vehicles built from Aug 2013

Versions by build date: Jun 2011 – Jul 2013 from Aug 2013


TERMINALS OF ECU
C238997E01
Text in Illustration 
*a
Component without harness connected
(Skid Control ECU [Brake Actuator Assembly])
Terminal No. (Symbol)
Terminal Description
1 (GND1)
Skid control ECU ground
2 (STP)
Stop light switch input
3 (IND)
Slip indicator light output
4 (RL-)
Rear wheel speed LH (-) signal input
5 (RL+)
Rear wheel speed LH (+) power supply output
6 (FR-)
Front wheel speed RH (-) signal input
7 (FR+)
Front wheel speed RH (+) power supply output
8 (BRL)
Brake warning light output
9 (EXI4)*1
L4 position switch input
10 (WA)
ABS warning light output
12 (+BS)
Solenoid relay power supply
13 (GND2)
Pump motor ground
14 (CANL)
CAN communication low line
15 (VSCW)
VSC OFF indicator light output
16 (RR-)
Rear wheel speed RH (-) signal input
17 (RR+)
Rear wheel speed RH (+) power supply output
18 (FL-)
Front wheel speed LH (-) signal input
19 (FL+)
Front wheel speed LH (+) power supply output
20 (EXI)*1
4WD detection switch input
23 (INFR)
TRC OFF indicator light output
24 (BM)
Motor relay power supply
25 (CANH)
CAN communication high line
27 (FSW+)
Brake pedal load sensing switch input
28 (EXI3)
w/o Rear Differential Lock: IG power supply input
w/ Rear Differential Lock: Rear differential lock position switch signal input
29 (PKB)
Parking brake switch input
30 (CSW)
VSC OFF switch input
32 (P)*2
Park/neutral position switch signal input
33 (TS)
Sensor check input
34 (IG1)
ECU power supply
  1. *1: for 4WD
  2. *2: for Automatic Transmission

TERMINAL INSPECTION

  1. C238998E01
    Disconnect the connector and measure the voltage or resistance according to the value(s) in the table below.
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU [Brake Actuator Assembly])

    HINT:
    The voltage cannot be measured with the connector connected to the skid control ECU (brake actuator assembly) as the connector is watertight.

    Standard 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    S35-1 (GND1) - Body ground
    W-B - Body ground
    Skid control ECU ground
    Always
    Below 1 Ω
    S35-2 (STP) - Body ground
    G-W - Body ground
    Stop light switch input
    Brake pedal depressed → released
    8 to 14 V
    → Below 1.5 V
    S35-9 (EXI4)*1 - Body ground
    G-W - Body ground
    L4 position switch input
    1. Ignition switch ON
    2. Transfer shift position not L4
    11 to 14 V
    S35-12 (+BS) - Body ground
    W-R - Body ground
    Solenoid relay power supply
    Always
    11 to 14 V
    S35-13 (GND2) - Body ground
    W-B - Body ground
    Pump motor ground
    Always
    Below 1 Ω
    S35-20 (EXI)*1 - Body ground
    R-B - Body ground
    4WD detection switch input
    1. Ignition switch ON
    2. Transfer shift position H2
    11 to 14 V
    S35-24 (BM) - Body ground
    R - Body ground
    Motor relay power supply
    Always
    11 to 14 V
    S35-27 (FSW+) - Body ground
    L - Body ground
    Brake pedal load sensing switch input
    Brake pedal depressed → released
    950 to 1050 Ω → 203 to 223 Ω
    S35-28 (EXI3) - Body ground
    V - Body ground
    w/o Rear Differential Lock: IG power supply input
    w/ Rear Differential Lock: Rear differential lock position switch signal input
    1. Ignition switch ON
    2. w/ Rear Differential Lock: Rear differential free
    11 to 14 V
    S35-29 (PKB) - Body ground
    L-O - Body ground
    Parking brake switch input
    1. Ignition switch ON
    2. Parking brake lever pulled → released
    Below 1 Ω → 10 kΩ or higher
    S35-30 (CSW) - Body ground
    R-L - Body ground
    VSC OFF switch input
    VSC OFF switch held → released
    Below 1 Ω → 10 kΩ or higher
    S35-32 (P)*2 - Body ground
    G-B - Body ground
    Park/neutral position switch signal input
    1. Ignition switch ON
    2. Shift lever not in P → Shift lever in P
    Below 1 V
    → 11 to 14 V
    S35-34 (IG1) - Body ground
    R-L - Body ground
    ECU power supply
    Ignition switch ON
    11 to 14 V
    1. *1: for 4WD
    2. *2: for Automatic Transmission

← TERMINALS OF ECU (Jun 2011 – Jul 2013)DIAGNOSIS SYSTEM (Jun 2011 – Jul 2013) →