2014 Hilux · Service Manual ENGINE

REASSEMBLY

Removal / installation · Vehicles built from Aug 2012

Versions by build date: Jun 2011 – Jul 2012 from Aug 2012


1. INSTALL OIL COOLER (for Automatic Transmission)

  1. A099950E04
    Install 2 new O-rings to the oil cooler.

  1. Install the oil cooler and 2 plate washers to the lower radiator tank with the 2 nuts.

    Torque:
    8.3 N*m{ 85 kgf*cm , 74 in.*lbf }

  1. Install the 2 cooler pipes.

    Torque:
    15 N*m{ 150 kgf*cm , 11 ft.*lbf }

    HINT:
    Set the cooler pipe labeled A to the location and angle shown in the illustration.


2. INSPECT LOCK PLATE FOR DAMAGE

  1. A099690E04
    Inspect the lock plate for damage.
    Text in Illustration 
    *1
    Lock Plate
    *2
    Core
    If the sides of the lock plate groove are deformed, reassembly of the tank will be impossible. Correct any deformations with pliers.
    Water will leak if the bottom of the lock plate groove is damaged or dented. Repair or replace it if necessary.

    NOTICE:
    The radiator can only be recaulked twice. After the second time, the radiator core must be replaced.


3. INSTALL UPPER RADIATOR TANK AND LOWER RADIATOR TANK

  1. A252179E01
    Check that there are no foreign objects in the lock plate groove, and then install a new O-ring. Make sure the O-ring is not twisted.
    Text in Illustration 
    *1
    O-Ring
    *a
    CORRECT
    *b
    INCORRECT
    *c
    Normal
    *d
    Twisted

    HINT:
    When cleaning the lock plate groove, lightly rub it with sandpaper without scratching it.

  1. Install the tank without damaging the O-ring.

  1. A110381E02
    Tap the lock plate with a plastic-faced hammer so that there is no gap between the lock plate and tank.
    Text in Illustration 
    *1
    Tank
    *2
    Lock Plate
    *a
    CORRECT
    *b
    INCORRECT


4. ASSEMBLE SST

  1. A234961E06
    Install the punch assembly to part A of the overhaul handle as shown in the illustration.
    SST
    09230-01010   (09231-01010, 09231-01020)
    09231-14010  
    Text in Illustration 
    *1
    Dimension B
    *2
    Part A
    *3
    Stopper Bolt

  1. While gripping the handle, adjust the stopper bolt so that dimension B is as specified below.

    Dimension B:
    8.4 mm (0.331 in.)


5. CAULK LOCK PLATE

  1. A099692E02
    Lightly press SST against the lock plate in the order shown in the illustration. After repeating this a few times, fully caulk the lock plate by squeezing the handle until stopped by the stopper bolt.
    SST
    09230-01010   (09231-01010, 09231-01020)
    09231-14010  
    Text in Illustration 
    *1
    Stopper Bolt
    *2
    Tank
    *3
    Lock Plate

    NOTICE:

    1. A099693E02
      Do not press the protruding areas around the ports (1) and bracket (2).

    2. A099694E01
      Do not use SST to press the areas indicated by the circle marks in the illustration. Use pliers and be careful not to damage the core plates.

  1. A099695E01
    Check the lock plate height H after completing the caulking.

    Standard plate height H:
    8.8 mm (0.346 in.)

    If the height is not as specified, readjust the stopper bolt of the handle and caulk the lock plate again.


6. INSTALL RADIATOR DRAIN COCK PLUG
  1. Install a new O-ring to the radiator drain cock plug.

  1. Install the radiator drain cock plug.


7. INSPECT FOR WATER LEAKS

  1. A099696E01
    Plug the inlet and outlet pipes of the radiator with SST.
    SST
    09230-01010   (09231-00030, 09231-00060)

  1. Using a radiator cap tester, apply pressure to the radiator.

    Standard test pressure:
    177 kPa (1.8 kgf/cm2, 26 psi)

  1. Submerge the radiator in water.

  1. A090282E04
    Inspect for leaks.
    Text in Illustration 
    *1
    Tank
    *2
    Lock Plate
    *3
    O-Ring

    HINT:
    On radiators with resin tanks, there is clearance between the tank and lock plate where a small amount of air will remain. This air is released when the radiator is submerged in water, giving the appearance of an air leak. Before performing the water leak test, first shake the radiator in the water until all air bubbles are released.


8. INSTALL RADIATOR BRACKET SUB-ASSEMBLY
  1. Install the 2 brackets with the 4 bolts.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }

← REASSEMBLY (Jun 2011 – Jul 2012)INSTALLATION (Jun 2011 – Jul 2012) →