2014 Hilux · Service Manual RESTRAINTS

B1900/73 Short in Front Driver Side Pretensioner Squib Circuit

Diagnostic trouble codes · Vehicles built from Aug 2014

Also covers:

Versions by build date: Jun 2011 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The driver side front pretensioner circuit consists of the center airbag sensor and the front seat outer belt driver side. The circuit instructs the SRS to deploy when deployment conditions are met. These DTCs are recorded when a malfunction is detected in the driver side front pretensioner circuit.
DTC No.
DTC Detection Condition
Trouble Area
B1900/73
When one of following conditions is met:
  1. Center airbag sensor assembly receives line short circuit signal 5 times in driver side front pretensioner circuit during primary check
  2. Front pretensioner driver side malfunction
  3. Center airbag sensor assembly malfunction
  1. Front seat outer belt assembly driver side (driver side front pretensioner)
  2. Center airbag sensor assembly
  3. Floor wire
B1901/73
When one of following conditions is met:
  1. Center airbag sensor assembly receives open circuit signal in driver side front pretensioner circuit for 2 seconds
  2. Front pretensioner driver side malfunction
  3. Center airbag sensor assembly malfunction
  1. Front seat outer belt assembly driver side (driver side front pretensioner)
  2. Center airbag sensor assembly
  3. Floor wire
B1902/73
When one of following conditions is met:
  1. Center airbag sensor assembly receives short circuit to ground signal in driver side front pretensioner circuit for 0.5 seconds
  2. Front pretensioner driver side malfunction
  3. Center airbag sensor assembly malfunction
  1. Front seat outer belt assembly driver side (driver side front pretensioner)
  2. Center airbag sensor assembly
  3. Floor wire
B1903/73
When one of following conditions is met:
  1. Center airbag sensor assembly receives short circuit to B+ signal in driver side front pretensioner circuit for 0.5 seconds
  2. Front pretensioner driver side malfunction
  3. Center airbag sensor assembly malfunction
  1. Front seat outer belt assembly driver side (driver side front pretensioner)
  2. Center airbag sensor assembly
  3. Floor wire

WIRING DIAGRAM

H101309E49

INSPECTION PROCEDURE


1. CHECK FRONT SEAT OUTER BELT ASSEMBLY DRIVER SIDE (DRIVER SIDE FRONT PRETENSIONER)
C305125E03
  1. Turn the ignition switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect the connector from the front seat outer belt driver side.

  1. Connect the white wire side of SST (resistance 2.1 Ω) to the floor wire connector C.

SST
09843-18060  

CAUTION:
Never connect a tester to the driver side front pretensioner for measurement, as this may lead to a serious injury due to airbag deployment.

NOTICE:
  1. Do not forcibly insert SST into the terminals of the connector when connecting.
  2. Insert SST straight into the terminals of the connector.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch OFF.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1900, B1901, B1902, B1903 or 73 is not output.

    HINT:
    DTCs other than DTC B1900, B1901, B1902, B1903 or 73 may be output at this time, but they are not related to this check.



NG
Go to step 2
OK

REPLACE FRONT SEAT OUTER BELT ASSEMBLY DRIVER SIDE (DRIVER SIDE FRONT PRETENSIONER)

2. CHECK CONNECTOR
  1. Turn the ignition switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect SST (resistance 2.1 Ω) from the floor wire.

  1. Check that the floor wire connector (on the front seat outer belt driver side) is not damaged.

    OK:
    The lock button is not disengaged, or the claw of the lock is not deformed or damaged.



NG
REPLACE FLOOR WIRE
OK


3. CHECK FLOOR WIRE
C305126E03
  1. Disconnect the connector from the center airbag sensor.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch ON.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    for LHD 
    Tester Connection
    Switch Condition
    Specified Condition
    F50-1(PD+) - Body ground
    Ignition switch ON
    Below 1 V
    F50-2(PD-) - Body ground
    Ignition switch ON
    Below 1 V
    for RHD 
    Tester Connection
    Switch Condition
    Specified Condition
    F51-1(PD+) - Body ground
    Ignition switch ON
    Below 1 V
    F51-2(PD-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    F50-1(PD+) - F50-2(PD-)
    Always
    Below 1 Ω
    F50-1(PD+) - Body ground
    Always
    1 MΩ or higher
    F50-2(PD-) - Body ground
    Always
    1 MΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    F51-1(PD+) - F51-2(PD-)
    Always
    Below 1 Ω
    F51-2(PD-) - Body ground
    Always
    1 MΩ or higher
    F51-1(PD+) - Body ground
    Always
    1 MΩ or higher

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    F50-1(PD+) - F50-2(PD-)
    Always
    1 MΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    F51-1(PD+) - F51-2(PD-)
    Always
    1 MΩ or higher



NG
REPLACE FLOOR WIRE
OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY


← B1900/73 Short in Front Driver Side Pretensioner Squib Circuit (+ B1901/73, B1902/73, B1903/73) (Aug 2013 – Jul 2014)B1905/74 Short in Front Passenger Side Pretensioner Squib Circuit (+ B1906/74, B1907/74, B1908/74) (Jun 2011 – Jul 2013) →