2014 Hilux · Service Manual RESTRAINTS

B1905/74 Short in Front Passenger Side Pretensioner Squib Circuit

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Also covers:

Versions by build date: Jun 2011 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The passenger side front pretensioner squib circuit consists of the center airbag sensor and the front seat outer belt passenger side. The circuit instructs the SRS to deploy when deployment conditions are met. These DTCs are recorded when a malfunction is detected in the passenger side front pretensioner squib circuit.
DTC No.
DTC Detection Condition
Trouble Area
B1905/74
When one of following conditions is met:
  1. Center airbag sensor assembly receives line short circuit signal 5 times in passenger side front pretensioner squib circuit during primary check
  2. Front pretensioner squib passenger side malfunction
  3. Center airbag sensor assembly malfunction
  1. Front seat outer belt assembly passenger side (passenger side front pretensioner squib)
  2. Center airbag sensor assembly
  3. Floor wire
B1906/74
When one of following conditions is met:
  1. Center airbag sensor assembly receives line open circuit signal 5 times in passenger side front pretensioner squib circuit for 2 seconds
  2. Front pretensioner squib passenger side malfunction
  3. Center airbag sensor assembly malfunction
  1. Front seat outer belt assembly passenger side (passenger side front pretensioner squib)
  2. Center airbag sensor assembly
  3. Floor wire
B1907/74
When one of following conditions is met:
  1. Center airbag sensor assembly receives short circuit to ground signal in passenger side front pretensioner squib circuit for 0.5 seconds
  2. Front pretensioner squib passenger side malfunction
  3. Center airbag sensor assembly malfunction
  1. Front seat outer belt assembly passenger side (passenger side front pretensioner squib)
  2. Center airbag sensor assembly
  3. Floor wire
B1908/74
When one of following conditions is met:
  1. Center airbag sensor assembly receives short circuit to B+ signal in passenger side front pretensioner squib circuit for 0.5 seconds
  2. Front pretensioner squib passenger side malfunction
  3. Center airbag sensor assembly malfunction
  1. Front seat outer belt assembly passenger side (passenger side front pretensioner squib)
  2. Center airbag sensor assembly
  3. Floor wire

WIRING DIAGRAM

H101309E06

INSPECTION PROCEDURE


1. CHECK FRONT SEAT OUTER BELT ASSEMBLY PASSENGER SIDE (PASSENGER SIDE FRONT PRETENSIONER SQUIB)
H101448E04
  1. Turn the ignition switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect the connector from the front seat outer belt passenger side.

  1. Connect the white wire side of SST (resistance 2.1 Ω) to the floor wire connector C.

SST
09843-18060  

CAUTION:
Never connect a tester to the passenger side front pretensioner squib for measurement, as this may lead to a serious injury due to airbag deployment.

NOTICE:
  1. Do not forcibly insert SST into the terminals of the connector when connecting.
  2. Insert SST straight into the terminals of the connector.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch OFF.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1905, B1906, B1907, B1908 or 74 is not output.

    HINT:
    DTCs other than DTC B1905, B1906, B1907, B1908 or 74 may be output at this time, but they are not related to this check.



OK
REPLACE FRONT SEAT OUTER BELT ASSEMBLY PASSENGER SIDE (PASSENGER SIDE FRONT PRETENSIONER SQUIB)
NG


2. CHECK CONNECTOR
  1. Turn the ignition switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect SST (resistance 2.1 Ω) from the floor wire.

  1. Check that the floor wire connector (on the front seat outer belt passenger side) is not damaged.

    OK:
    The lock button is not disengaged, or the claw of the lock is not deformed or damaged.



NG
REPAIR OR REPLACE FLOOR WIRE
OK


3. CHECK FLOOR WIRE
H100394E19
  1. Disconnect the connector from the center airbag sensor.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch ON.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    for LHD 
    Tester Connection
    Specified Condition
    F22-1 - Body ground
    Below 1 V
    F22-2 - Body ground
    Below 1 V
    for RHD 
    Tester Connection
    Specified Condition
    F21-1 - Body ground
    Below 1 V
    F21-2 - Body ground
    Below 1 V

  1. Turn the ignition switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    for LHD 
    Tester Connection
    Specified Condition
    F22-1 - F22-2
    Below 1 Ω
    F22-1 - Body ground
    1 MΩ or higher
    F22-2 - Body ground
    1 MΩ or higher
    for RHD 
    Tester Connection
    Specified Condition
    F21-1 - F21-2
    Below 1 Ω
    F21-1 - Body ground
    1 MΩ or higher
    F21-2 - Body ground
    1 MΩ or higher

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    for LHD 
    Tester Connection
    Specified Condition
    F22-1 - F22-2
    1 MΩ or higher
    for RHD 
    Tester Connection
    Specified Condition
    F21-1 - F21-2
    1 MΩ or higher



NG
REPAIR OR REPLACE FLOOR WIRE
OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY


← B1905/74 Short in Front Passenger Side Pretensioner Squib Circuit (+ B1906/74, B1907/74, B1908/74) (Jun 2011 – Jul 2013)B1905/74 Short in Front Passenger Side Pretensioner Squib Circuit (+ B1906/74, B1907/74, B1908/74) (from Aug 2014) →