2014 Hilux · Service Manual DRIVE LINE

REPLACEMENT

Removal / installation · Vehicles built Jun 2011 – Jul 2014

Versions by build date: Jun 2011 – Jul 2014 from Aug 2014


1. DRAIN TRANSFER OIL

2. REMOVE LOWER TRANSFER CASE PROTECTOR

  1. F043499
    Remove the 4 bolts and protector.


3. REMOVE FRONT PROPELLER SHAFT ASSEMBLY
  1. TMT made:
    Remove the front propeller shaft (Click here).

  1. TSAM made:
    Remove the front propeller shaft (Click here).


4. REMOVE OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY
  1. Using a chisel and hammer, loosen the staked part of the lock nut.

  1. F043429E01
    Using SST to hold the companion flange, remove the lock nut.
    SST
    09330-00021  

  1. F043430E01
    Using SST, remove the companion flange.
    SST
    09950-40011   (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04051, 09957-04010, 09958-04011)


5. REMOVE TRANSFER CASE OIL SEAL

  1. F043485E01
    Using SST, tap out the oil seal.
    SST
    09308-00010  

    NOTICE:
    Be careful not to damage the oil seal and case front contact surface.


6. INSTALL TRANSFER CASE OIL SEAL
  1. Coat the lip of a new oil seal with MP grease.

  1. F043487E01
    Using SST and a hammer, tap in the oil seal until its surface is flush with the case upper surface.
    SST
    09316-60011   (09316-00011)


7. INSTALL OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY

F044048E01
  1. Apply gear oil to the connecting areas of the companion flange and driven sprocket.

  1. Install the companion flange to the driven sprocket.

  1. Using SST to hold the companion flange, install a new lock nut.

    SST
    09330-00021  
    09950-40011   (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04051, 09957-04010, 09958-04011)

    Torque:
    118 N*m{ 1,203 kgf*cm , 87 ft.*lbf }

  1. F050151E01
    Using a chisel and hammer, stake the lock nut to the driven sprocket.

    NOTICE:
    1. Thoroughly stake the shaft to the lock nut's groove.
    2. Be careful not to damage parts around the lock nut.
    3. Do not apply excessive force to the shaft.


8. INSTALL FRONT PROPELLER SHAFT ASSEMBLY
  1. TMT made:
    Install the front propeller shaft (Click here).

  1. TSAM made:
    Install the front propeller shaft (Click here).


9. INSTALL LOWER TRANSFER CASE PROTECTOR

  1. F043499
    Install the protector with the 4 bolts.

    Torque:
    18 N*m{ 183 kgf*cm , 13 ft.*lbf }


10. ADD TRANSFER OIL
  1. Remove the case plug (for filler) and gasket.

  1. Pour oil so that the oil level is between 0 to 5.0 mm (0 to 0.197 in.) from the bottom lip of the case plug (for filler) hole.

    NOTICE:
    1. When adding oil, pour it slowly.
    2. Add oil a little at a time, waiting several minutes between each addition of oil.

  1. Wait approximately 5 minutes and check that the oil level has not changed.

  1. Install a new gasket and the case plug (for filler).

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

← COMPONENTS (from Jun 2011)REPLACEMENT (from Aug 2014) →