P0105 Manifold Absolute Pressure / Barometric Pressure Circuit
Diagnostic trouble codes · Vehicles built Jun 2011 – Jul 2012
Also covers:
- P0107 Manifold Absolute Pressure / Barometric Pressure Circuit Low Input
- P0108 Manifold Absolute Pressure / Barometric Pressure Circuit High Input
Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION


The manifold absolute pressure sensor detects the intake manifold pressure by using the built-in sensor unit. The ECM determines the basic injection duration and injection advance timing based on the voltage output by the manifold absolute pressure sensor.
The manifold absolute pressure sensor monitors the absolute pressure inside the intake manifold (default is 0 kPa (0 mmHg, 0 in.Hg)). As a result, the ECM controls the air-fuel ratio at the proper level under any driving conditions, and is not influenced by fluctuations in the atmospheric pressure due to factors such as high altitude, etc.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0105 P0107 P0108 |
Open or short in manifold absolute pressure sensor circuit for 0.5 seconds or more (1 trip detection logic) |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- If DTCs related to different systems that have terminal E2 as the ground terminal are output simultaneously, terminal E2 may have an open circuit.
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, and other data from the time the malfunction occurred.
- If DTCs related to different systems that have terminal E2 as the ground terminal are output simultaneously, terminal E2 may have an open circuit.
- NOTICE:
- If the ECM is replaced, the new ECM needs initialization (Click here).
| 1. READ VALUE USING INTELLIGENT TESTER (MAP) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON and turn the intelligent tester ON.
Enter the following menus: Powertrain / Engine / Data List / MAP.
Read the values.
- Standard:
- Same value as the actual atmospheric pressure.
|
|
||||
| NG | |
| 2. CHECK ECM (VC VOLTAGE) |
![]() ![]() |
Turn the ignition switch ON.
Measure the voltage of the ECM connector.
- Standard voltage:
Tester Connection
Specified Condition
E8-18 (VC) - E8-28 (E2)
4.5 to 5.5 V
|
|
||||
| OK | |
| 3. CHECK ECM (PIM VOLTAGE) |
![]() ![]() |
Turn the ignition switch ON.
Measure the voltage of the ECM connectors.
- Standard voltage:
Tester Connection
Condition
Specified Condition
E7-28 (PIM) - E8-28 (E2)
Applied negative pressure of 40 kPa (300 mmHg, 11.8 in.Hg)
1.3 to 1.9 V
E7-28 (PIM) - E8-28 (E2)
Same as atmospheric pressure
2.4 to 3.1 V
E7-28 (PIM) - E8-28 (E2)
Applied positive pressure of 170 kPa (1,275 mmHg, 50.2 in.Hg)
3.7 to 4.3 V
|
|
||||
| NG | |
| 4. CHECK WIRE HARNESS (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM) |
![]() ![]() |
Disconnect the T9 sensor connector.
Disconnect the E7 and E8 ECM connectors.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
Specified Condition
T9-2 (PIM) - E7-28 (PIM)
Below 1 Ω
T9-3 (VC) - E8-18 (VC)
Below 1 Ω
T9-1 (E2) - E8-28 (E2)
Below 1 Ω
T9-2 (PIM) or E7-28 (PIM) - Body ground
10 kΩ higher
T9-3 (VC) or E8-18 (VC) - Body ground
10 kΩ higher
T9-1 (E2) or E8-28 (E2) - Body ground
10 kΩ higher
|
|
||||
| OK | |
| 5. INSPECT TURBOCHARGER SUB-ASSEMBLY |
- OK:
- None of the inspection results show any abnormalities.
|
|
||||
| OK | |
| 6. INSPECT EGR VALVE ASSEMBLY |
- OK:
- None of the inspection results show any abnormalities.
|
|
||||
| OK | ||
| ||



