2014 Hilux · Service Manual BODY ELECTRICAL

Display Signal Circuit between Radio and Display Assembly and Television Camera Assembly

Circuit diagnosis · Vehicles built Aug 2012 – Jul 2013

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013

DESCRIPTION

The display signal from the rear television camera assembly transmits to the radio and display receiver assembly.

WIRING DIAGRAM

E224825E02

INSPECTION PROCEDURE


1. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)
  1. Disconnect the R18 radio and display receiver assembly connector.

  1. Disconnect the T41 rear television camera assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R18-7 (CA+) - T41-4 (CB+)
    Always
    Below 1 Ω
    R18-8 (V+) - T41-2 (CV+)
    Always
    Below 1 Ω
    R18-15 (CGND) - T41-3 (CGND)
    Always
    Below 1 Ω
    R18-16 (V-) - T41-1 (CV-)
    Always
    Below 1 Ω
    R18-7 (CA+) - Body ground
    Always
    10 kΩ or higher
    R18-8 (V+) - Body ground
    Always
    10 kΩ or higher
    R18-15 (CGND) - Body ground
    Always
    10 kΩ or higher
    R18-16 (V-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY

  1. E224536E02
    Disconnect the R18 radio and display receiver assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R18-16 (V-) - Body ground
    Always
    Below 1 Ω
    R18-15 (CGND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Radio and Display Receiver Assembly)



NG
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)
OK


3. CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY

  1. E227664E07
    Disconnect the T41 rear television camera assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    T41-4 (CB+) - T41-3 (CGND)
    Ignition switch ON, shift lever in R
    5.5 to 7.05 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Rear Television Camera Assembly)



NG
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)
OK


4. CHECK REAR TELEVISION CAMERA ASSEMBLY

  1. Using an oscilloscope, check the waveform.E224537E02

    HINT:
    A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the radio and display receiver assembly with the connector connected.

    Text in Illustration 
    *a
    Component with harness connected
    (Radio and Display Receiver Assembly)
    *b
    Waveform 1
    *c
    Waveform 2
    *d
    Synchronized Signal
    *e
    Video Waveform
    -
    -
    Measurement Condition 
    Item
    Content
    Terminal No. (Symbol)
    R18-8 (V+) - R18-16 (V-)
    Tool Setting
    0.2 V/DIV., 50 μs/DIV.
    Condition
    1. Waveform 1: Ignition switch ON, shift lever in R
    2. Waveform 2: Ignition switch ON, shift lever in R, screen blacked out by covering camera lens

    OK:
    Waveform is as shown in the illustration.

    HINT:
    The video waveform changes according to the image sent by the rear television camera assembly.



NG
REPLACE REAR TELEVISION CAMERA ASSEMBLY (Click here)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)


← Display Signal Circuit between Radio and Display Assembly and Television Camera Assembly (Jun 2011 – Jul 2012)Display Signal Circuit between Radio and Display Assembly and Television Camera Assembly (from Aug 2013) →