2014 Hilux · Service Manual ENGINE

P0046 Turbocharger / Supercharger Boost Control Solenoid Circuit Range / Performance

Diagnostic trouble codes · Vehicles built Aug 2012 – Jul 2013

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

Variable nozzle vane type turbocharger consists primarily of a compressor wheel, turbine wheel, nozzle vane, unison ring, DC motor and nozzle vane position sensor.
The ECM outputs a signal to the turbo motor driver, which actuates the DC motor, to control the nozzle vane position.
DTC No.
DTC Detection Condition
Trouble Area
P0046
Either of following conditions met:
  1. DC motor duty ratio +/- 100% for 1.3 seconds or more
  2. DC motor current 2.2 A or more for 5 seconds or more when motor driving
    (1 trip detection logic)
  1. DC Motor (Turbocharger sub-assembly)
  2. Turbo Motor Driver

WIRING DIAGRAM

A155054E08

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).


1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO P0046)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    P0046
    A
    P0046 and other DTCs
    B

    HINT:
    If any DTCs other than P0046 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2. INSPECT TURBOCHARGER SUB-ASSEMBLY (DC MOTOR OPERATION)
  1. Turn the ignition switch ON.

  1. Turn the ignition switch OFF and check the DC motor operation.

    OK:
    When ignition switch is turned OFF, operation link moves as shown in A through D in illustration below.
    Operation link and motor rod move smoothly when moving from position shown in A to that shown in B, and from position shown in B to that shown in C.

A158317E01


NG
Go to step 3
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)

3. INSPECT TURBO MOTOR DRIVER

  1. Voltage Inspection

    1. A158418E22
      Turn the ignition switch ON (IG).

    2. Measure the voltage between the terminals of the turbo motor driver connector.

      Standard voltage:
      Tester Connection
      Specified Condition
      +B (T8-3) - GND (T8-4)
      11 to 14 V

  1. Output Waveform Inspection

    1. A227095E11
      Turn the ignition switch ON (IG).

    2. Check the waveform of the ECM connectors using an oscilloscope.

      OK:
      Tester Connection
      Condition
      Specified Condition
      VNTI (T8-2) - GND (T8-4)
      Ignition switch ON
      Correct waveform is as shown



NG
REPLACE TURBO MOTOR DRIVER
OK


4. INSPECT TURBOCHARGER SUB-ASSEMBLY (DC MOTOR RESISTANCE)

  1. G036521E03
    Disconnect the T10 DC motor connector.

  1. Measure the resistance of the DC motor.

    Standard resistance:
    Tester Connection
    Specified Condition
    M+ (2) - M- (1)
    1 to 100 Ω



NG
REPLACE TURBOCHARGER SUB-ASSEMBLY (Click here)
OK


5. CHECK HARNESS AND CONNECTOR (DC MOTOR - TURBO MOTOR DRIVER)

  1. A150170E08
    Disconnect the T10 DC motor connector.

  1. Disconnect the T8 turbo motor drive connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    M+ (T8-12) - M+ (T10-2)
    Below 1 Ω
    M- (T8-5) - M- (T10-1)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    M+ (T8-12) or M+ (T10-2) - Body ground
    10 kΩ or higher
    M- (T8-5) or M- (T10-1) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. CHECK IF DTC OUTPUT RECURS (DTC P0046)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Clear the DTC (Click here).

  1. Start the engine.

  1. Perform the test drive.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    P0046
    A
    No output
    B



B
END
A

REPLACE TURBOCHARGER SUB-ASSEMBLY (Click here)


← P0046 Turbocharger / Supercharger Boost Control Solenoid Circuit Range / Performance (Jun 2011 – Jul 2012)P0046 Turbocharger / Supercharger Boost Control Solenoid Circuit Range / Performance (Aug 2013 – Jul 2014) →