2014 Hilux · Service Manual RESTRAINTS

B1630/23 Driver Side Rear Airbag Sensor Circuit Malfunction

Diagnostic trouble codes · Vehicles built Jun 2011 – Jul 2013

Versions by build date: Jun 2011 – Jul 2013 from Aug 2013

DESCRIPTION

The rear airbag sensor (driver side) consists of the safing sensor, the diagnostic circuit, the lateral deceleration sensor, etc.
If the center airbag sensor receives signals from the lateral deceleration sensor, it determines whether the SRS should be activated.
DTC B1630/23 is recorded when a malfunction is detected in the rear airbag sensor (driver side) circuit.
DTC Code
Detection Condition
Trouble Area
B1630/23
Both conditions below are met:
  1. Driver side - rear airbag sensor malfunction
  2. Center airbag sensor malfunction
  1. Side airbag sensor (driver side)
  2. Rear airbag sensor (driver side)
  3. Floor wire
  4. Center airbag sensor assembly

WIRING DIAGRAM

C194828E09
C194828E10

INSPECTION PROCEDURE


1. CHECK VEHICLE CONDITION
  1. Check vehicle condition.

    Result 
    Result
    Proceed to
    for RHD
    A
    for LHD
    B



B
Go to step 7
A


2. CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the side airbag sensor RH and rear airbag sensor RH.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


3. CHECK CONNECTORS
  1. Disconnect the connectors from the side airbag sensor RH and rear airbag sensor RH.

  1. Check that the connectors (on the side airbag sensor RH side and rear airbag sensor RH side) are not damaged.

    OK:
    The connectors are not deformed or damaged.



NG
REPLACE FLOOR WIRE
OK


4. CHECK REAR AIRBAG SENSOR RH CIRCUIT
C194787E08
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    R13-2 (BCR+) - Body ground
    Ignition switch ON
    Below 1 V
    R13-1 (BCR-) - Body ground

  1. Turn the ignition switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Using a service wire, connect terminals 1 (BCR+) and 2 (BCR-) of connector B.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    R13-2 (BCR+) - R13-1 (BCR-)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    R13-2 (BCR+) - R13-1 (BCR-)
    Always
    1 MΩ or higher
    R13-2 (BCR+) - Body ground
    R13-1 (BCR-) - Body ground



NG
REPLACE FLOOR WIRE
OK


5. CHECK REAR AIRBAG SENSOR RH
C241359E01
  1. Connect the connector to the side airbag sensor RH.

  1. Interchange the rear airbag sensor RH with LH and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch OFF.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC B1630 and B1635 are not output
    A
    DTC B1635 is output
    B
    DTC B1630 is output
    C

    HINT:
    Codes other than DTC B1630 and B1635 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Return the rear airbag sensor LH and RH to their original positions and connect the connectors to them.



A
USE SIMULATION METHOD TO CHECK

B
REPLACE REAR AIRBAG SENSOR RH
C


6. CHECK SIDE AIRBAG SENSOR RH
C158841E08
  1. Interchange the side airbag sensor RH with LH and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch OFF.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC B1630 and B1635 are not output
    A
    DTC B1630 is output
    B
    DTC B1635 is output
    C

    HINT:
    Codes other than DTC B1630 and B1635 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Return the side airbag sensor LH and RH to their original positions and connect the connectors to them.



A
USE SIMULATION METHOD TO CHECK

B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY
C

REPLACE SIDE AIRBAG SENSOR RH

7. CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the side airbag sensor LH and rear airbag sensor LH.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


8. CHECK CONNECTORS
  1. Disconnect the connectors from the side airbag sensor LH and rear airbag sensor LH.

  1. Check that the connectors (on the side airbag sensor LH side and rear airbag sensor LH side) are not damaged.

OK:
The connectors are not deformed or damaged.



NG
REPLACE FLOOR WIRE
OK


9. CHECK REAR AIRBAG SENSOR LH CIRCUIT
C194787E09
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    R14-2 (BCL+) - Body ground
    Ignition switch ON
    Below 1 V
    R14-1 (BCL-) - Body ground

  1. Turn the ignition switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Using a service wire, connect terminals 2 (BCL-) and 1 (BCL+) of connector B.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    R14-2 (BCL+) - R14-1 (BCL-)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    R14-2 (BCL+) - R14-1 (BCL-)
    Always
    1 MΩ or higher
    R14-2 (BCL+) - Body ground
    R14-1 (BCL-) - Body ground



NG
REPLACE FLOOR WIRE
OK


10. CHECK REAR AIRBAG SENSOR LH
C241359E02
  1. Connect the connector to the side airbag sensor LH.

  1. Interchange the rear airbag sensor LH with RH and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch OFF.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC B1630 and B1635 are not output
    A
    DTC B1635 is output
    B
    DTC B1630 is output
    C

    HINT:
    Codes other than DTC B1630 and B1635 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Return the rear airbag sensor RH and LH to their original positions and connect the connectors to them.



A
USE SIMULATION METHOD TO CHECK

B
REPLACE REAR AIRBAG SENSOR LH
C


11. CHECK SIDE AIRBAG SENSOR LH
C158841E02
  1. Interchange the side airbag sensor LH with RH and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch OFF.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC B1630 and B1635 are not output
    A
    DTC B1630 is output
    B
    DTC B1635 is output
    C

    HINT:
    Codes other than DTC B1630 and B1635 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Return the side airbag sensor RH and LH to their original positions and connect the connectors to them.



A
USE SIMULATION METHOD TO CHECK

B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY
C

REPLACE SIDE AIRBAG SENSOR LH


← B1625/22 Front Passenger Side - Side Airbag Sensor Circuit Malfunction (from Aug 2013)B1630/23 Driver Side Rear Airbag Sensor Circuit Malfunction (from Aug 2013) →