B1635/24 Front Passenger Side Rear Airbag Sensor Malfunction
Diagnostic trouble codes · Vehicles built Jun 2011 – Jul 2013
Versions by build date: Jun 2011 – Jul 2013 from Aug 2013
DESCRIPTION
The rear airbag sensor (front passenger side) consists of the safing sensor, the diagnostic circuit, the lateral deceleration sensor, etc.If the center airbag sensor receives signals from the lateral deceleration sensor, it determines whether the SRS should be activated.
DTC B1635/24 is recorded when a malfunction is detected in the rear airbag sensor (front passenger side) circuit.
| DTC Code |
Detection Condition |
Trouble Area |
| B1635/24 |
Both conditions below are met:
|
|
WIRING DIAGRAM




INSPECTION PROCEDURE
| 1. CHECK VEHICLE CONDITION |
Check vehicle condition.
Result Result
Proceed to
for LHD
A
for RHD
B
|
|
||||
| A | |
| 2. CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch OFF.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the side airbag sensor RH and rear airbag sensor RH.
- OK:
- The connectors are properly connected.
|
|
||||
| OK | |
| 3. CHECK CONNECTORS |
Disconnect the connectors from the side airbag sensor RH and rear airbag sensor RH.
Check that the connectors (on the side airbag sensor RH side and rear airbag sensor RH side) are not damaged.
- OK:
- The connectors are not deformed or damaged.
|
|
||||
| OK | |
| 4. CHECK REAR AIRBAG SENSOR RH CIRCUIT |


Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch ON.
Measure the voltage according to the value(s) in the table below.
- Standard voltage:
Tester Connection
Switch Condition
Specified Condition
R13-2 (BCR+) - Body ground
Ignition switch ON
Below 1 V
R13-1 (BCR-) - Body ground
Turn the ignition switch OFF.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Using a service wire, connect terminals 1 (BCR+) and 2 (BCR-) of connector B.
- NOTICE:
- Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
R13-2 (BCR+) - R13-1 (BCR-)
Always
Below 1 Ω
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
R13-2 (BCR+) - R13-1 (BCR-)
Always
1 MΩ or higher
R13-2 (BCR+) - Body ground
R13-1 (BCR-) - Body ground
|
|
||||
| OK | |
| 5. CHECK REAR AIRBAG SENSOR RH |
![]() ![]() |
Connect the connectors to the side airbag sensor RH.
Interchange the rear airbag sensor RH with LH and connect the connectors to them.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch OFF.
Turn the ignition switch ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
Result Result
Proceed to
DTC B1630 and B1635 are not output
A
DTC B1630 is output
B
DTC B1635 is output
C
- HINT:
- Codes other than DTC B1630 and B1635 may be output at this time, but they are not related to this check.
Turn the ignition switch OFF.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Return the rear airbag sensor LH and RH to their original positions and connect the connectors to them.
|
|
||||
|
|
||||
| C | |
| 6. CHECK SIDE AIRBAG SENSOR RH |
![]() ![]() |
Interchange the side airbag sensor RH with LH and connect the connectors to them.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch OFF.
Turn the ignition switch ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
Result Result
Proceed to
DTC B1630 and B1635 are not output
A
DTC B1635 is output
B
DTC B1630 is output
C
- HINT:
- Codes other than DTC B1630 and B1635 may be output at this time, but they are not related to this check.
Turn the ignition switch OFF.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Return the side airbag sensor LH and RH to their original positions and connect the connectors to them.
|
|
||||
|
|
||||
| C | ||
| ||
| 7. CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch OFF.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the side airbag sensor LH and rear airbag sensor LH.
- OK:
- The connectors are properly connected.
|
|
||||
| OK | |
| 8. CHECK CONNECTORS |
Disconnect the connectors from the side airbag sensor LH and rear airbag sensor LH.
Check that the connectors (on the side airbag sensor LH side and rear airbag sensor LH side) are not damaged.
- OK:
- The connectors are not deformed or damaged.
|
|
||||
| OK | |
| 9. CHECK REAR AIRBAG SENSOR LH CIRCUIT |


Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch ON.
Measure the voltage according to the value(s) in the table below.
- Standard voltage:
Tester Connection
Switch Condition
Specified Condition
R14-2 (BCL+) - Body ground
Ignition switch ON
Below 1 V
R14-1 (BCL-) - Body ground
Turn the ignition switch OFF.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Using a service wire, connect terminals 2 (BCL-) and 1 (BCL+) of connector B.
- NOTICE:
- Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
R14-2 (BCL+) - R14-1 (BCL-)
Always
Below 1 Ω
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
R14-2 (BCL+) - R14-1 (BCL-)
Always
1 MΩ or higher
R14-2 (BCL+) - Body ground
R14-1 (BCL-) - Body ground
|
|
||||
| OK | |
| 10. CHECK REAR AIRBAG SENSOR LH |
![]() ![]() |
Connect the connectors to the side airbag sensor LH.
Interchange the rear airbag sensor LH with RH and connect the connectors to them.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch OFF.
Turn the ignition switch ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
Result Result
Proceed to
DTC B1630 and B1635 are not output
A
DTC B1630 is output
B
DTC B1635 is output
C
- HINT:
- Codes other than DTC B1630 and B1635 may be output at this time, but they are not related to this check.
Turn the ignition switch OFF.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Return the rear airbag sensor RH and LH to their original positions and connect the connectors to them.
|
|
||||
|
|
||||
| C | |
| 11. CHECK SIDE AIRBAG SENSOR LH |
![]() ![]() |
Interchange the side airbag sensor LH with RH and connect the connectors to them.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch OFF.
Turn the ignition switch ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
Result Result
Proceed to
DTC B1630 and B1635 are not output
A
DTC B1635 is output
B
DTC B1630 is output
C
- HINT:
- Codes other than DTC B1630 and B1635 may be output at this time, but they are not related to this check.
Turn the ignition switch OFF.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Return the side airbag sensor RH and LH to their original positions and connect the connectors to them.
|
|
||||
|
|
||||
| C | ||
| ||



