2014 Hilux · Service Manual ENGINE

P2009 Intake Manifold Runner Control Circuit Low (Bank 1)

Diagnostic trouble codes · Vehicles built Aug 2012 – Jul 2013

Also covers:

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

Refer to DTC P2006 (Click here).
DTC No.
DTC Detection Condition
Trouble Area
P2009
Open in VSV for swirl control valve circuit for 0.5 seconds
(2 trip detection logic)
  1. VSV for swirl control valve (Intake manifold)
  2. Open in VSV for swirl control valve circuit
  3. ECM
P2010
Short in VSV for swirl control valve circuit for 0.5 seconds
(2 trip detection logic)
  1. VSV for swirl control valve (Intake manifold)
  2. Short in VSV for swirl control valve circuit
  3. ECM

WIRING DIAGRAM

Refer to DTC P2006 (Click here).

INSPECTION PROCEDURE

NOTICE:
If the ECM is replaced, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE VACUUM SWITCHING VALVE FOR SWIRL CONTROL VALVE)

  1. A067588E05
    Connect an intelligent tester to the DLC3.

  1. Disconnect the vacuum hoses from the VSV for swirl control valve.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Select the following menu items: Powertrain / Engine and ECT / Active Test / Activate the VSV for Swirl Control Valve.

  1. Check the operation.

    OK:
    When VSV for swirl control valve is ON, air from port E flows out through port F.
    When VSV for swirl control valve is OFF, air from port E flows out through air filter.



OK
CHECK FOR INTERMITTENT PROBLEMS
NG


2. INSPECT VACUUM SWITCHING VALVE FOR SWIRL CONTROL VALVE (RESISTANCE)

  1. A150435E06
    Disconnect the S9 vacuum hoses from the VSV for swirl control valve connector.

  1. Measure the resistance of the VSV.

    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    37 to 44 Ω



NG
REPLACE INTAKE MANIFOLD
OK


3. INSPECT VACUUM SWITCHING VALVE FOR SWIRL CONTROL VALVE (POWER SOURCE VOLTAGE)

  1. A154589E04
    Disconnect the S9 vacuum hoses from the VSV for swirl control valve connector.

  1. Turn the ignition switch ON.

  1. Measure the voltage between the terminal of the wire harness side connector and body ground.

    Standard voltage:
    Tester Connection
    Specified Condition
    VSV for swirl control valve (S9-1) - Body ground
    11 to 14 V



OK
Go to step 5
NG


4. CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY (MAIN RELAY) - VACUUM SWITCHING VALVE FOR SWIRL CONTROL VALVE)

  1. G034915E21
    Remove the No. 1 integration relay from the engine room junction block (Click here).

  1. Disconnect the 1J No. 1 integration relay connector.

  1. Disconnect the S9 VSV connector.

  1. Measure the resistance of the wire harness side connectors.

Standard resistance (Check for open):
Tester Connections
Specified Conditions
1J-5 - S9-2
Below 1 Ω

Standard resistance (Check for short):
Tester Connections
Specified Conditions
1J-5 or S9-2 - Body ground
10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE POWER SOURCE CIRCUIT COMPONENTS

5. CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE FOR SWIRL CONTROL VALVE - ECM)

  1. G034916E02
    Disconnect the S9 VSV connector.

  1. Disconnect the E6 ECM connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    S9-1 - E8-15 (SCV)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    S9-1 or E8-15 (SCV) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM


← P2009 Intake Manifold Runner Control Circuit Low (Bank 1) (+ P2010) (Jun 2011 – Jul 2012)P2009 Intake Manifold Runner Control Circuit Low (Bank 1) (+ P2010) (Aug 2013 – Jul 2014) →