P2009 Intake Manifold Runner Control Circuit Low (Bank 1)
Diagnostic trouble codes · Vehicles built Aug 2012 – Jul 2013
Also covers:
- P2010 Intake Manifold Runner Control Circuit High (Bank 1)
Versions by build date: Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
Refer to DTC P2006 (Click here).| DTC No. |
DTC Detection Condition |
Trouble Area |
| P2009 |
Open in VSV for swirl control valve circuit for 0.5 seconds (2 trip detection logic) |
|
| P2010 |
Short in VSV for swirl control valve circuit for 0.5 seconds (2 trip detection logic) |
|
WIRING DIAGRAM
Refer to DTC P2006 (Click here).INSPECTION PROCEDURE
- NOTICE:
- If the ECM is replaced, the new ECM needs registration (Click here) and initialization (Click here).
- HINT:
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, and other data from the time the malfunction occurred.
| 1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE VACUUM SWITCHING VALVE FOR SWIRL CONTROL VALVE) |
Connect an intelligent tester to the DLC3.

Disconnect the vacuum hoses from the VSV for swirl control valve.
Turn the ignition switch ON and turn the tester ON.
Select the following menu items: Powertrain / Engine and ECT / Active Test / Activate the VSV for Swirl Control Valve.
Check the operation.
- OK:
- When VSV for swirl control valve is ON, air from port E flows out through port F.
When VSV for swirl control valve is OFF, air from port E flows out through air filter.
|
|
||||
| NG | |
| 2. INSPECT VACUUM SWITCHING VALVE FOR SWIRL CONTROL VALVE (RESISTANCE) |
Disconnect the S9 vacuum hoses from the VSV for swirl control valve connector.

Measure the resistance of the VSV.
Tester Connection
Condition
Specified Condition
1 - 2
20°C (68°F)
37 to 44 Ω
|
|
||||
| OK | |
| 3. INSPECT VACUUM SWITCHING VALVE FOR SWIRL CONTROL VALVE (POWER SOURCE VOLTAGE) |
Disconnect the S9 vacuum hoses from the VSV for swirl control valve connector.

Turn the ignition switch ON.
Measure the voltage between the terminal of the wire harness side connector and body ground.
- Standard voltage:
Tester Connection
Specified Condition
VSV for swirl control valve (S9-1) - Body ground
11 to 14 V
|
|
||||
| NG | |
| 4. CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY (MAIN RELAY) - VACUUM SWITCHING VALVE FOR SWIRL CONTROL VALVE) |
Remove the No. 1 integration relay from the engine room junction block (Click here).

Disconnect the 1J No. 1 integration relay connector.
Disconnect the S9 VSV connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance (Check for open):
Tester Connections
Specified Conditions
1J-5 - S9-2
Below 1 Ω
- Standard resistance (Check for short):
Tester Connections
Specified Conditions
1J-5 or S9-2 - Body ground
10 kΩ or higher
|
|
||||
| OK | ||
| ||
| 5. CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE FOR SWIRL CONTROL VALVE - ECM) |
Disconnect the S9 VSV connector.

Disconnect the E6 ECM connector.
Check the resistance.
- Standard resistance (Check for open):
Tester Connection
Specified Condition
S9-1 - E8-15 (SCV)
Below 1 Ω
- Standard resistance (Check for short):
Tester Connection
Specified Condition
S9-1 or E8-15 (SCV) - Body ground
10 kΩ or higher
|
|
||||
| OK | ||
| ||
